ULTRALOQ Bolt Fingerprint Smart Lock with Handle

Please scan the QR code to watch the installation video.

Or you can also view the website directly. www.ultraloq.com/Bolt_F_Wi-Fi/guide

Check the door's dimensions.

Measure to confirm that the door is between 1^3 / 8^''∼1^3 / 4^'' (35 mm-45 mm) thick.

Note: If your door is thicker than 1^{3/4} , please visit www.ultraloq.com to order the "ULTRALOQ Thick Door Kit".

Measure to confirm that the diameter of the hole is 2^{1/8} (53 mm) or 1^{1/2} (38 mm)

Measure to confirm that the backset is either 2^{3/8} or 2^{3/4} (60 mm or 70 mm).

Measure to confirm that the diameter of the hole in the door edge is 1^{\prime \prime} (25 mm).

Measure to confirm the depth of the hole in the frame is at least 1^{\prime \prime}(25mm)

If you have a new door, please drill the holes according to Drill Template.

Insert the bolt into the door. Making sure the "UP ↑" icon faces upward.

Note: By default, the bolt is set to a 2-3/8" (60mm) backset.

To adjust to 2-3/4" (70mm): Make sure the bolt is fully retracted.

Press the bolt, then twist it until you feel a slight click. This locks it in the extended backset position.

Note: Always ensure the bolt is retracted before making adjustments.

Align the strike plate with the door frame.

Secure it in place using the provided screws A(x4)

Ensure the bolt is fully retracted.

Make sure the cylinder tailpiece is horizontal, with the bump pointing upward.

Carefully install the Exterior Assembly onto the door.

Do not insert the mechanical key during installation.

Carefully thread the cable through the hole located below the bolt to the interior side of the door.

If your door has a 1 1/2”(38 mm) bore hole, remove the spacer as shown. If not, don't remove it.

Route the cable through the hole in the Interior Assembly Mounting Plate.

Secure the Interior Assembly Mounting Plate to the Exterior Assembly using Screw B(x2).

Warning: Do not install the batteries before installing the interior assembly, as this may prevent the keypad from powering on properly.

Remove the battery cover from the Interior Assembly.

Insert the cable connector into the socket on the Interior Assembly.

Ensure the white-painted side is facing up.

Press the connector firmly until it is fully seated.

Rotate the knob to the vertical position to keep the lock unlocked during installation.

Align the Interior Assembly with Mounting Plate.

Use Screw C(x2) to secure the Interior Assembly in place.

This step helps your lock learn which way your door opens, so it can work properly.

Rotate the knob to the vertical position to keep the lock unlocked.

Insert 8 AA alkaline batteries into the battery compartment. Keep the batteries resting on the battery pull tab for easy removal later.

Reattach the battery cover.

Note: Only the Program Code on the battery cover can unlock Bolt Series in Factory Default Mode.

Keep the bolt in the unlocked position, then press and hold the "5" key for 3 seconds until you hear 2 beeps.

The lock will automatically rotate and begin

self-calibrating the door direction, which will complete in approximately 5 seconds.

Note: To prevent deadbolt jamming, ensure this step is performed after the lock is installed on the door.

Door sensor lets you know whether the door is open or closed through the App. When Auto-Lock is enabled, your LOCK will automatically lock only when the door is fully closed.

Do not mount the door sensor on the keypad side of the lock. Avoid installing the sensor on metal doors that interfere with the internal magnet. (In such cases, the door sensor may stick to the metal door magnetically and malfunction.)

The sensor is suitable for:

Wooden doors.

Metal doors that do not interfere with the sensor's

magnetic field (i.e., the sensor does not stick magnetically to the door).

Drill two holes at the marked positions.

Press the door sensor against the wall and secure it using Screws D (x2).

Attach the door sensor cover by sliding it from top to bottom along the chute until it clicks into place.

Note: Door sensor should be mounted as close to the edge of your door frame as possible, or within 0 to 1^{" "} (25 mm) from the edge, and as close to the bottom of the extended deadbolt as possible, or within 0 to 1^{" "} (25 mm) from the edge.

Note: Please refer to the guide in U home app for more information.

Please scan the QR code on the left to watch the user guide video. You can also visit the website directly at www.ultraloq.com/Bolt_F_Wi-Fi/guide.

For the configuration guide for integrations (Alexa, Google Assistant, IFTTT, Apple Home, and SmartThings), please scan the QR code on the right or visit

support.ultraloq.com, then choose "Works with" to watch the user guide video.

Lights up when an incorrect code is entered or a failed operation occurs.

Warns when the battery power is running low.

Verifies your fingerprint to unlock the door from the outside.

Used to manually lock/unlock the door, illuminate the keypad, and confirm actions.

Allows mechanical key access in case of battery failure or in other emergency situations.

Supports secure code entry by allowing random digits before or after the correct code.

Flashes when the lock is communicating with your app or smart home system.

Lights up to confirm successful code entry or programming.

One-touch locking

Confirm unlocking after entering the password

Illuminate the keypad

Step1 Input Password

Tap to lock when going outside

Step 2 Tap

Illuminate the keyboard in darkness

Used to reset the lock to Factory Default settings.

To reset, use a Reset Needle to press and hold the reset button (located under the battery cover) for about 10 seconds until you hear one long beep followed by two short beeps.

Note: If the lock was paired with an app, please first tap "Remove Device" in the app before resetting. For detailed reset instructions, refer to Page 14.

Use the tab to lift and remove the batteries from the battery compartment easily.

Hold 8 AA alkaline Batteries.

Note: Insert 8 AA alkaline Batteries or UTEC Lithium Batteries. Rechargeable or other battery types are not recommended.

Protects the battery compartment and includes labels for the Program Code and (optionally) the Apple HomeKit setup code.

Used to manually lock and unlock the door from inside.

Turns green when the door is unlocked.

When the battery is low, the lock will beep three times, and the Low Battery Indicator will illuminate.

Note: Please replace the batteries promptly to avoid lock failure.

Scan QR code to download the App

Download on the

App Store

GETITON

Google Play

Scan the QR code to download the app, or search for:

- "U home" in the App Store (iOS). "U home" in the Google Play Store (Android).

- Open the U home app. - Create an account or log in with your existing credentials.

- Ensure the lock is in Factory Default Mode. To reset your lock to Factory Default Mode, please refer to Page 14. - Turn on Bluetooth on your smartphone. - Stay within 10 feet of the lock. - Search for the lock within the app.

- Follow the on-screen instructions in the app to complete pairing. - Ensure your phone is connected to a 2.4GHz Wi-Fi network.

5GHz Wi-Fi networks are not supported.

You can program the lock manually in Standalone Mode. See the guide on Page 15 for instructions.

You can unlock the LOCK using any of the following methods:

Enter your 4-8 digit code, then press the ULTRALOQ button to unlock.

Place your finger on Fingerprint Reader to unlock.

Unlock via Bluetooth or Wi-Fi using the U home app. Refer to the in-app guide for setup, pairing, and remote access.

Press ULTRALOQ button to lock manually.

Enable Auto Lock feature and the lock to automatically relock after the door is closed.

Rotate the interior thumb turn to the vertical position to unlock.

Resetting will erase all data and restore factory default settings

1. Open the app and click "Remove Device" to remove the lock from your U home app. 2. You will hear 1 long beep followed by 2 short beeps, confirming the reset was successful.

1. Use a Reset Needle to press the Reset Button under the battery cover. 2. Hold for 10 seconds, until you hear 1 long beep followed by 2 short beeps.

Use 8 high-quality AA alkaline batteries when power is low or depleted. Open the battery cover and replace all batteries at once for optimal performance.

Keep at least one Backup Key in a secure location outside your home in case of battery failure.

You can enable or disable the Auto Lock feature directly from the keypad:

Ensure the bolt is in the unlocked position.

Press and hold the "1" button for 3 seconds.

The Checkmark Indicator will light up green and you'll heart two beeps.

Ensure the bolt is in the unlocked position.

Press and hold the "O" button for 3 seconds.

The Checkmark Indicator will light up green and you'll hear two beeps.

Tip: You can also enable/disable Auto Lock and customize the relock delay in the U home app.

The lock supports a Vague Code (anti-peep feature) of up to 16-digits. As long as your correct user code appears in the correct sequence within the digits entered, the door will unlock.

User Code: 123456 Valid Vague Code

123456XXXXXX

XXXXX123456

XX123456XX

"X" represents any random digit. The correct code must appear in order, even if surrounded by other digits.

Bottom View

Top View

Side View

1. For a higher recognition rate, please try to cover the Fingerprint Reader completely with your finger, touching the surrounding metal ring. 2. Make sure that your finger and Fingerprint Reader are clean and dry. For Fingerprint Reader, use a clean, lint-free cloth to wipe off any dirt or debris. 3. Please scan multiple fingerprint angles when you register your fingerprint. 4. While scanning your finger, you shouldn't tap too quickly or move your finger around.

Note: It is recommended to use the U home app to program your lock. If you don't have a smartphone or prefer not to use the app, you can follow the steps below.

Warning: Standalone Mode is NOT available once the lock is registered in the app. To enable Standalone Mode, you must reset the lock to Factory Default Mode first.

To add the Admin Code, you need the Program Code found on the battery cover.

Operation

Hold (UTRALOQ) for 3 sec

LED & Sound Indicator

Enter your Admin Code and press (ULTRALOG)

2 beeps with light on

Enter a 4-8 digit User Code and press UTRALOQ

2 beeps with \odot light on

Re-enter the User Code and press ULTRALQ

2 beeps with \odot light on

Success

2 beeps with \odot light on

All lights off

Operation

LED & Sound Indicator

Hold ULTRALOG for 3 sec

2 beeps with light on

Enter your Admin Code and press (ulTRALQ)

2 beeps with \odot light on

Press Fingerprint 6 times

5 beeps and digit buttons blink 5 times

Success

All lights off

To delete the Admin and all Users Codes, reset the lock to Factory Default Mode.

Use a Reset Needle to press the Reset Button (located under the battery cover).

Hold for 10 seconds, until you hear 1 long beep followed by 2 short beeps.

The lock is now reset and ready to be programmed again in Standalone Mode. 16

Resetting will erase all data and restore factory default settings.

If registered in the U home app: Tap "Remove Device" in the app. The lock will automatically reset.

If in Standalone Mode: Use a Reset Needle to press the Reset Button (under the battery cover) for 10 seconds, until you hear 1 long beep followed by 2 short beeps.

Visit www.uhomelabs.com/account.

Or login to the U home app on another smartphone or tablet.

Change your U home Account password to secure your device.

When the battery is low, the lock will emit three beeps and the low battery indicator will light up.

Replace the batteries as soon as possible.

If the battery is fully drained, use the backup key to unlock the door.

Please keep at least one backup key in secure location outside your home.

It is recommended to use the original ULTRALOQ accessories for best performance and stability.

The lock can store up to 50 users, and each user can register 1 code and 2 fingerprints. It can also store up to 1,000 activity logs. Once it's full, the newest entries will automatically overwrite the oldest.

Disable Remote Access to Lock in the U home app to significantly extend battery life.

Note: Disabling this will turn off remote features including Alexa, Google Assistant, IFTTT, Apple Home, SmartThings and smart notifications.

No, the lock has built-in Wi-Fi and does not require an external hub.

The lock supports 2.4GHz Wi-Fi only. 5Ghz Wi-Fi is not supported.

The Program Code is a unique 6-digit code found on the battery cover. It is required to unlock the lock in Factory Default Mode and to initialize programming in Standalone Mode.

A Brand of Xthings