SwitchBot S10

Robot Components

Note: Press any button to stop the robot during cleaning or docking.

Robot Bottom View Dustbin Components Waste Water Box Components

Waste Water Box Lid

Air Extraction Port

Waste Water Inlet

Full Water Detection Float

Auto-empty Station Front View Back View

Before starting the robot, please check the floor and clean up any scattered items such as wires, socks, slippers, children's toys, etc. to improve the efficiency of the robot.

Clear the floor of hard or sharp objects (e.g., nails, glass), and move away items that are fragile, valuable, or potentially dangerous to avoid being caught, tangled, or knocked over by the robot, causing personal or property damage.

Before cleaning, please use a physical barrier to avoid areas that are hanging in the air or low, ensuring the safety and smooth operation of your robot.

Open the doors of the rooms to be cleaned, arrange the furniture neatly, and try to clear the largest cleaning space.

Please avoid standing in front of your robot, doorways, or narrow passages in case your robot cannot detect the area to be cleaned.

1. When using the robot for the first time, follow it throughout its whole cleaning route and watch for potential problems. This will help you identify and resolve minor issues, ensuring a more efficient cleaning process in the future.

2. If the robot gets stuck under low furniture, you can try the following solutions:

① Block the bottom of the furniture; ② Set a virtual wall in the app to prevent the robot from entering; ③ If possible, raise the furniture slightly.

1 Place the Auto-empty Station on a hard, level surface (such as a floor or ceramic tile) against a wall, ensuring there is at least 1 meter of space in front and above, and 0.5 meters on both sides. Make sure the location has a good Wi-Fi signal to provide a better network connection and app user experience. Plug the Auto-empty Station into an outlet, ensure the indicator light turns on, and store any excess cable in the Cord Wrap.

- The power cord may be dragged by the robot if hanging on the ground, causing the Auto-empty Station to move or disconnect from power. - The indicator light on the Auto-empty Station will stay on when powered, and go off when the robot is charging. - If there is an issue with the Auto-empty Station, the indicator light will turn red and stay on as a reminder. - Make sure to place the Auto-empty Station on a level indoor surface, away from open flames, heat sources, water, narrow spaces, or areas that may cause the robot to hang in the air. - Placing the Auto-empty Station on non-hard surfaces (such as carpets, mats, etc.) poses a risk of tipping over, and the robot may not be able to leave the Auto-empty station properly. - Do not place the Auto-empty Station under direct sunlight or block its signal emitter area with any objects, as this may prevent the robot from returning automatically. - Please maintain the Auto-empty Station according to the maintenance instructions and avoid using wet cloths or wipes for cleaning.

Tip:

When you hear a clicking sound, it means the Side Brush has been properly installed.

1 Remove the faceplate as shown in the picture, and turn on the Power Switch. "I" means powering on, and "O" means powering off.

2 Wait for the indicator light on your robot to light on, then manually dock your robot to the Auto-empty Station to charge, as shown in the picture. You will hear the voice prompt "Charging".

To maintain battery performance, please keep the robot charged during daily use. - Before using the robot for the first time, it is recommended to charge it for a while. If it cannot be turned on, it might be due to insufficient battery. Please dock the robot directly to the Auto-empty Station.

Please activate the Water Station before use:

Press and hold the Bluetooth Reset Button for 2 seconds until the indicator light flashes white.

Please note:

If activation fails, use a 5 V 2 A Type-C charger to charge the Water Station for 6 hours first.

Please follow the User Manual of SwitchBot Floor Cleaning Robot S10 Water Station to install your Water Station.

support.switch-bot.com/hc/en-us/sections/18659086869911

Setup Guide

1. The Water Station has two connected hoses on its back, one for water inlet, and one for water draining. The inlet hose can be connected to your home's water inlet system to provide clean water for mopping and washing the Roller Mop. The drain hose can be connected to your home's drain system, to discharge the waste water. 2. Water inlet requirements: water pressure should be between 0.1MPa to 0.6MPa , and water temperature should be below 40°C . 3. Please refrain from using old hose sets when setting up your appliance.

• Download the SwitchBot app to experience more personalized settings and a better user experience.

You will need:

- A smartphone or tablet using Bluetooth 4.2 or later. - The latest version of our app, downloadable via the Apple App Store or Google Play Store. - A SwitchBot account, you can register via our app or sign in to your account directly if you already have one.

iOS 14.0+ Android OS 5.0+

Open our app, tap "+" located at the right-handed corner of the home page, select Add Device. ③ Find the device icon and select, follow the instructions to add your device.

Before mapping, make sure your robot is docked to the Autoempty Station and is charged. Then follow the in-app instructions to start mapping. Your robot will automatically return to the Autoempty Station once mapping is complete, and will save its progress. Tip: When using for the first-time, short press the (0) button, and your robot will start mapping while cleaning. 2 You will need to mark the position of the Water Station on your map once it is created. Please follow the in-app instructions to complete.

Please note:

- If your robot failed to find the Water Station when marking, you can try the following manually dock your robot to the Water Station. When successfully docked, press the button, and your robot will leave the Water Station, relocate itself, then return to the Auto-empty Station. - If you move the Water Station after marking its position, remember to update its position via the app.

After marking the Water Station position, control your robot via our app or press the button on the robot to start. Your robot will start cleaning from the Auto-empty Station.

1 Press the button on your robot, and your robot will plan the cleaning route dynamically based on the scanned map.

Before mopping, your robot will go to the Water Station (marked) to add clean water first, then return to the task starting point to start.

Note: For first-time use, your robot will automatically work on the Vacuum mode.

3 During the cleaning process, your robot will determine the timing for exchanging water itself. It will automatically return to the Water Station, drain the waste water and replenish clean water to ensure good cleaning performance.

- To facilitate the normal water exchange of the robot, please do not move the Water Station during the cleaning and mopping process. If there is a door hiding the Water Station, please keep the door open. If the battery is low, please charge it before starting the cleaning task. - If the battery is insufficient during the cleaning process, the robot will automatically return to the Auto-empty Station for charging. - When the robot is set to clean carpets, it will automatically raise the Roller Mop when detected. You can choose to bypass carpets in our app. Before starting each mopping task, please make sure that the Roller Mop is correctly installed.

Press the button once to change the cleaning mode of your robot. You will hear a sound and voice prompt when the mode switches successfully. It will be set to Vacuum mode by default.

In Vacuum mode, the Roller Mop will automatically raise and stop rolling.

Press any button on your robot to stop it while working. When paused, tap the \odot button to resume the previous cleaning task, tap the \odot button to finish the task, and your robot will go to the Water Station first to exchange water and then return to the Auto-empty Station to recharge.

1 While vacuuming or mopping, your robot will automatically go to the Water Station to exchange water if needed, and then go back to its previous position to resume cleaning. After finishing a cleaning task, your robot will go to the Water Station first, have a deep cleaning and replenish clean water, then return to Auto-empty Station to recharge.

After finishing a cleaning task, your robot will automatically return to Auto-empty Station to recharge. To manually send it back to recharge, press the ⊙ button on your robot. The indicator light will be breathing when charging.

If the robot does not find the Auto-empty Station, it will automatically return to the starting position. Please manually dock it to the Auto-empty Station for charging.

If your robot is not operated for more than 10 minutes, it will automatically enter hibernation. Press any button to wake it up.

Please note: The robot will not enter hibernation while charging.

The default setting for this mode is from 22:00 to 08:00, and you can modify or disable it via our app. During the Do Not Disturb period, device button lights will stay off, and your robot will not automatically resume cleaning or play voice prompts.

You can use the Child Lock function in our app to lock the robot buttons. You can unlock it via our app.

Press and hold the (∙) + (∙) + (∙) button simultaneously for 6 seconds to restore the robot to factory settings. The voice prompt will say, "Restoring to factory settings."

To keep your robot running at peak performance, care and maintain your robot regularly as shown in the sheet below.

Replacement frequency may vary. Parts should be replaced if visible wear appears.

For free replacement parts, please contact our customer support at support@switch-bot.com

If you need to purchase a refill of SwitchBot Floor Cleaning Solution, please visit the authorized channels or our official website www.switchbot.com

1 Remove the Waste Water Box from the robot and open the lid.

2 Clean the sediment inside the Waste Water Box.

Note: Avoid getting water into the Air Extraction Port during the cleaning process.

Install the Waste Water Box back to the robot.

Before flipping the robot over to clean, empty the Waste Water Box first to prevent waste water spillage.

1 Remove the Roller Mop from the robot.

Filp the robot over, and lift the Waste Water Collection Gutter from its left end to remove.

3 Clean the sediment inside the Waste Water Collection Gutter.

4 Install the Waste Water Collection Gutter back into the robot by putting its right end into the robot first, then press its left end into the robot to secure. You will hear a clicking sound once it is correctly installed.

Install the Roller Mop back to the robot.

1 Flip the robot over, press the latch, and remove the brush cover.

2 Remove the Anti-Tangle Rubber Brush, pull out the bearings at both ends, and clean any hair or dirt wrapped around the brush. You can use the provided small cleaning tool for this.

Install the Anti-Tangle Rubber Brush back to the robot. You will hear a clicking sound once it is correctly installed. Make sure both ends of the brush are inserted into the robot's pegs, and then cover it with the brush cover.

- Wipe off the dirt on the Anti-Tangle Rubber Brush with a damp cloth. If the brush is soaked, dry it thoroughly and avoid direct sunlight. - Do not use corrosive cleaning liquids or disinfectants to clean the Anti-Tangle Rubber Brush.

1 Remove the Side Brush.

Clean the Side Brush and its mounting shaft, then reinstall it.

Use a small screwdriver or similar tool to pry out the wheel and clean it.

2 Rinse the wheel and axle to remove hair or dirt. Dry it and reattach the wheel, pressing it firmly into place.

1 Open the robot's cover and remove the dustbin.

Open the dustbin lid and empty the trash. You can use the small cleaning tool provided for this.

\Theta Reinstall the dustbin.

If washing, do not add any detergent, as it may cause filter clogging. Make sure to dry the dustbin and the filter thoroughly before installing them back.

2 Rinse the filter repeatedly and gently tap the dirt out until it is clean.

Do not touch the filter surface with hands, brushes, or sharp objects to avoid damaging the filter.

1 Open the dustbin cover and remove the filter.

- Allow the filter to air dry for at least 24 hours before reusing. It is recommended to alternate using the two filters.

1 As shown in the picture, lift the Roller Mop Cover and pull out the Roller Mop.

Use the small cleaning tool provided to remove hair or debris wrapped around the Roller Mop.

3 Rinse the Roller Mop surface with clean water and drain excess water.

4 Reinstall the Roller Mop and press the Roller Mop Cover back into place. Make sure there is no water or stains inside the Roller Mop to avoid damaging the motor.

Do not rinse the roller motor directly with water, as it may cause damage to the motor and the robot.

Clean the various sensors on the robot with a soft, dry cloth, including: LDS Laser Radar, Docking Sensors, Obstacle Avoidance Sensor, Wall Follow Sensor, Carpet Sensor, Cliff Sensor, and Charging Contacts.

When the dust bag is full, replace it according to the indicator light on your Auto-empty Station (orange flashing quickly) or the app notification. It is recommended to replace the dust bag every 8 to 10 weeks.

Open the canister lid, remove and discard the used dust bag.

Tip:

When removing the dust bag, its handle will seal the bag to effectively prevent dust leakage.

Install a new dust bag and close the canister lid.

The canister lid cannot be closed without a dust bag in the Auto-empty Station. Do not force it shut.

Use the small cleaning tool provided to clear any debris accumulated in the Debris Evacuation Port.

Use a dry cloth to wipe the Debris Evacuation Port to make sure it is dry and clean.

If the Debris Evacuation Tube is blocked, follow these steps to clean it:

1 Flip the Auto-empty Station with the bottom facing up, unscrew the Debris Evacuation Tube cover, and remove it.

2 Check for any blockages in the Debris Evacuation Tube and use the small cleaning tool provided to help clear them.

Use a dry cloth to wipe the Debris Evacuation Tube and the cover.

4 Reinstall the Debris Evacuation Tube cover as shown in the picture.

Use a soft, dry cloth to clean the Auto-empty Station's charging contacts and the Recharging Signal Emitter area.

1 Follow the mark beside the Waste Filter Cover on the Water Station to turn it open.

2 Remove the Waste Filter inside, and rinse it under a tap.

3 Insert the Waste Filter back into the Water Station, tighten the knob, put the cover back, and place the Water Station at its original position.

1 Open the rubber seal of the cleaning solution inlet on the Water Station.

Pour the SwitchBot Floor Cleaning Solution inside, and tighten the seal.

- Do not add any non-official cleaning solution or disinfectants into the Water Station. - Should you use cleaning solution inside your Water Station, we strongly advise using this product to refill any humidifier, as traces of cleaning solution may remain.

Use a soft, dry cloth to clean the Water Station's charging contacts and the Recharging Signal Emitter area.

- The battery level is low. Put the robot on the charging station and charge it before use. - The ambient temperature is too low or too high. Only use the robot within the range of 4°C to 40°C (39°F to 104°F).

- The Auto-empty Station is not powered, please make sure both ends of the power cord are plugged in properly. - Poor contact, please clean the charging contacts on the Auto-empty Station and the robot.

- Incorrect Wi-Fi password, please enter the correct Wi-Fi password. - Switch to a 2.4GHz network for pairing, as 5GHz networks and enterprise routers are not supported. - Keep the robot within a range with good Wi-Fi signal strength. - The robot may not be in the ready-to-configure state, exit the app and re-enter, then follow the pairing steps to try again.

- The robot needs to start mapping from the Auto-empty Station, it is recommended to use the Fast Mapping feature. - Do not move the robot during the first mapping process to avoid locating failure. - If the robot does not return to the Auto-empty Station after completing the first mapping task, check if it has returned properly and remove any obstacles on the ground obstructing it.

- The Auto-empty Station lost power or the robot was moved while being outside. - The charging route is blocked, such as a closed door. - Too many obstacles near the Auto-empty Station, please place it in an open area. - After moving the robot, it will relocate itself. If locating fails, it will generate a new map. If the Auto-empty Station is too far away, it may not be able to recharge, please manually dock the robot back to the Auto-empty Station to charge. - Wipe the signal emission area of the Auto-empty Station in case there is dust or dirt. - Gently wipe the front Obstacle Avoidance Sensor of the robot with a soft, dry cloth and keep the lens clean and unobstructed.

- The robot takes about 6 hours to charge from low to full battery. - In high or low-temperature environments, the robot will automatically reduce charging speed to extend battery life. - The charging contact area may be dirty, please wipe it with a dry cloth.

- Please turn off and restart the robot.

- Please reinstall the Side Brush, making sure to hear a "click" to indicate it is in place. - The Side Brush may have fallen off due to tangled wires. Please clear wires on the floor before use.

- The dustbin is full. Please empty it. - The filter may be clogged with dust. Please check and clean as necessary. - If the filter is not dry after cleaning. Please let it air dry before using.

Dust leaked while working

Remove the Anti-Tangle Rubber Brush and dustbin, and clear any debris near the Anti-Tangle Rubber Brush.

Loud operating noise

The dustbin is full. Please empty it. Hard objects may be tangled in the Anti-Tangle Rubber Brush and dustbin. Please check and clean as necessary. The Side Brush and Anti-Tangle Rubber Brush may be tangled with debris. Please check and clean as necessary. You can lower the suction power of the robot to Quiet or Low if necessary.

Abnormal sound emitted while moving

Rotate and press the wheels to check for any debris tangled or stuck. Clean the debris or or contact customer service if the issue persists.

Random movement path

Loose wires, slippers, and other objects on the floor may affect the robot's normal operation. Please tidy up before use. Working on wet and slippery floors may cause the wheels to slip. Please manually wipe or air dry the floor before using.

Stopped due to being stuck

The robot may be stuck under furniture of a similar height. Consider raising the furniture, manually blocking or using our app to set a virtual wall to avoid the area. Check the corresponding area for any wires, curtains, or carpet edges that may be tangled with or obstructing the robot. Manually remove any obstructions for smooth operation.

Name: SwitchBot Floor Cleaning Robot S10 Battery: 21.6 V / 4000 mAh lithium-ion battery System Requirements: iOS 14.0+, Android OS 5.0+ Network Connectivity: 2.4 GHz Wi-Fi, Bluetooth 4.2 Rated Power: 85 W Charging Time: 6 h

Rated Input: 220\sim 240V50 / 60Hz Rated Power (Charging):36 W Rated Power (Emptying Dust):800 W Rated Power (Drying Mop and Charging):200 W Rated Output: 24V = 1.5A