Shark POWERDETECT Ultra-Light Corded Stick Vacuum with DuoClean Technology

In Detect mode, Floor Detect technology automatically senses carpets and hard floors and adjusts the brushroll speed for optimal performance. The Floor Detect display indicates which surface type has been detected.

(L)-Hard Floor (R)-Carpet

Press the Mode Button to deactivate Floor Detect and switch to the manual Hard Floor mode for surfaces like wood or tile. Press the Mode button again to switch to the manual Carpet mode for both low and high pile carpets.

NOTE: For deep cleaning per ASTM F608 (embedded dirt in carpets) please use the Carpet setting. NOTE: Select Carpet for stuck-on dust and debris.

ODOR DIAL

Flip up the dial handle and rotate the odor dial to adjust Odor Neutralizer Technology intensity or to unlock the dial for cartridge access.

Insertion/Removal: Rotate the odor dial to align the teal arrows. Remove the dial to access the odor cartridge for removal or replacement.

Low: Rotate the dial toward the Low position to decrease the intensity to the lowest level when the vacuum is in use.

High: Rotate the dial toward the High position for the highest intensity level when the vacuum is in use. This position is the recommended setting for optimal performance.

• Remove odor cartridge from dial if you don’t want the benefits of Odor Neutralizer Technology.

• Clean all filters as recommended under Cleaning Filters.
• Empty the dust cup before storing your vacuum.
• Replace the cartridge as recommended under Odor Cartridge Replacement.
• Visit qr.sharkclean.com/odortech to learn more and purchase replacements.
• If wet pet messes are cleaned up, thoroughly clean the vacuum.

• The intensity of the fragrance may diminish over time. It may also have no noticeable fragrance at all. This is natural and does not indicate the technology isn’t working. Follow replacement instructions to ensure continued performance.

NOTES: • The odor dial needs to be installed for the vacuum to function properly, with or without the odor cartridge.

• Odor Neutralizer Technology effectively deodorizes while interacting with odors from inanimate sources.

1. REMOVE ODOR DIAL FROM NOZZLE 2. REMOVE OLD ODOR CARTRIDGE

Flip up the handle and rotate the dial clockwise until the two teal arrows are aligned. Pull the handle to remove the dial from the nozzle.

Rotate the cartridge counterclockwise in the dial housing and pull out the cartridge to remove it.

3.REMOVE NEW CARTRIDGE FROM BAG 4. INSTALL NEW CARTRIDGE IN DIAL

Remove the new odor cartridge from the sealed packaging. To maintain the life of the cartridge, keep it in the sealed packaging until you are ready to install it.

Align the yellow arrow on the side of the cartridge with the yellow arrow on the side of the dial cover, then insert the cartridge into the dial. Rotate the cartridge clockwise to lock it in place.

5. INSTALL DIAL IN NOZZLE 6. USED CARTRIDGE DISPOSAL

Align the teal arrow on the dial cover with the teal arrow on the nozzle, then reinsert the dial into the nozzle. Rotate the dial counterclockwise until it clicks into an intensity setting to engage. Rotate further to change the intensity setting.

Dispose of the old cartridge by dropping it into the trash.

NOTE: Odor cartridges should be replaced every 6 months for optimal Odor Neutralizer Technology performance.

FLOOR MODE

To clean floors, step on floor nozzle and tilt handheld vacuum back.

ABOVE-FLOOR WITH WAND

For more reach, detach the wand. Stand the vacuum upright, step on the Foot Pedal on the side of the nozzle, and pull up the wand to detach.

ABOVE-FLOOR HANDHELD

To detach the handheld vacuum, press the Wand Release button and lift the handheld vacuum off the wand. Great for cleaning stairs, furniture, and countertops.

STAIR CLEANING

To clean stairs or other narrow spaces, attach the handheld vacuum to the floor nozzle.

NOTE: All accessories are compatible with both the wand and the handheld vacuum.

Return the vacuum to its upright position. Once the Upright Lock engages, the vacuum will stand freely.

Wrap the cord around the two cord hooks. Start with the bottom hook and leave a little slack in the cord.

Press the Wand Release button near the top of the wand to detach the handheld vacuum. Align the Catch on the side of the handheld vacuum with the Storage Hook on the wand, then hang the handheld vacuum from the hook.

Wrap the cord around the two cord hooks. Start with the top hook, and leave a little slack in the cord.

IMPORTANT: Unplug the vacuum before performing any maintenance.

Empty the dust cup each time you vacuum and periodically during cleaning, when debris in the dust cup reaches the MAX fill line.

Press the Wand Release button and lift off the handheld vacuum. To remove the dust cup from the handheld vacuum, press the two Dust Cup Release buttons at the same time and pull out the dust cup from the top. Hold the dust cup over the trash. Pull back on the yellow Empty button and pull up to open the dust cup lid until it clicks and locks in the open position. Gently tap the coneshaped screen inside the dust cup to knock dust and debris into the trash. To reinstall, push the lid closed, then insert the dust cup into the handheld vacuum from the top, until it clicks into place.

IMPORTANT: Unplug the vacuum before performing any maintenance.

Regularly rinse and replace the filters to maintain your vacuum's suction power and to maximize the effectiveness of Odor Neutralizer Technology. To prevent damage from cleaning chemicals, rinse filters with cold water only. Do not use soap. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electronic parts.

PRE-MOTOR FILTERS

The Pre-Motor Filters should be rinsed every month. To remove the pre-motor filters, detach the dust cup, then slide down the Filter Access buttons on both sides of the dust cup lid. Pull out the filter housing, then lift out the Foam Filter. Next, remove the Felt Filter by the pull tab. After the filters have been rinsed and are completely dry, insert the foam filter into the housing first, then slide in the felt filter, and reinstall the housing into the dust cup lid.

HEPA FILTER

The HEPA Filter should be rinsed every 6 months. To remove the HEPA filter, detach the dust cup, then pull the Filter Release tab on the handheld vacuum filter cover. Remove the cover, then squeeze the side tabs on the HEPA filter and lift it out. After the filter has been rinsed and is completely dry, reinsert it into the handheld vacuum, then reattach the filter cover.

NOTE: The pre-motor filters should be replaced every 2.5 years. The post-motor filter should be replaced every 3 years.

HEADLIGHTS The headlights will flash or turn red to indicate issues that need attention.

Solid White Lights: The brushroll is spinning and the unit is working as it should.

Solid Red Lights: There is a jam in the brushroll area. Turn off the vacuum and unplug it, then remove any blockages in the nozzle.

Flashing Red Lights: The motorized floor nozzle is overheating. Turn off the vacuum, unplug it, and remove any blockages. Let the vacuum cool down for at least 60 minutes before restarting. See Troubleshooting section for more information.

Flashing White Lights: The vacuum is operating in an environment that is either too hot or too cold. This vacuum will only function properly in temperatures ranging from 32° F ( O ° C ) to 104° F (40° C ) . Turn the vacuum off and adjust the room temperature.

CHECK HANDHELD

Remove the handheld vacuum from the wand and check all dust cup intake openings for debris or blockages.

CHECK WAND

Detach the wand and check it for blockages.

CHECK FLOOR NOZZLE

Detach the wand, turn the nozzle over, open the Nozzle Hose Access, and check for blockages.

FLOOR DETECT™ SENSOR

Make sure to clean the Detect sensors regularly, as hair and other debris may build up and obstruct them. If the sensors are partially obstructed, Detect mode will not function as expected.

1. Step on the foot pedal to detach the nozzle from the wand. 2. Turn the nozzle over and locate the Floor Detect sensor on the bottom. 3. Use a cotton swab to wipe away dirt and debris from the sensor and surrounding area.

If any hair is wrapped around the brushroll, continue vacuuming, using Carpet mode on a hard floor surface, a low-pile carpet, or a small area rug. This will allow the self-cleaning brushroll to remove the hair wrap and send it to the dust cup.

If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll. If some fibers remain wrapped around the brushroll after continued use, clear them from the brushroll.

1. To remove the Soft Roller, slide the Eject Roller Button on the floor nozzle. 2. Tap loose debris off the Soft Roller. Use a dry towel to wipe it clean, and to remove any debris caught in the teeth behind the Soft Roller. 3. Hand-wash the Soft Roller as needed. Use only water, let it air-dry completely for at least 24 hours. 4. Reinsert the Soft Roller and press it in until it clicks securely into place.

NOTE: For best performance, keep the Soft Roller clean with regular maintenance.

If your vacuum has low suction or no suction, or if it is struggling to pick up debris while moving in reverse, then you’ll need to remove and clean the Squeegee Bristle Strip on the bottom of the nozzle. To access the squeegee strip, step on the foot pedal to detach the nozzle from the wand.

REMOVE SCREWS REMOVE SQUEEGEE

1. Turn the nozzle over and locate the squeegee bristle strip between the brushroll and the rear wheels. Use a Phillips-head screwdriver to remove the 4 screws.

2. Remove the squeegee strip by pulling up on the fabric flaps on both ends of the strip.

NOTE: Keep screws after removal.

CLEANING THE CAVITY

1. With the strip removed, clean the squeegee cavity and bristle strip. Use a paper towel to wipe off any debris or dust in the cavity and on the bristle strip.

SQUEEGEE REPLACEMENT

1. Hold the squeegee strip by the fabric flaps on the ends, with the bristle side facing up. Insert the plastic piece into the cavity first, while tilting the strip forward, toward the brushroll.

LINE UP SCREW HOLES

2. Align the 4 screw holes on the squeegee strip over the holes in the nozzle. Make sure the strip sits flush with the nozzle, then fasten it securely in place with the screws.

1. DO NOT pull or carry vacuum cleaner by the cord or use cord as a handle. 2. DO NOT unplug by pulling on the cord. Grasp the plug, not the cord. 3. DO NOT close the door on the cord. 4. DO NOT pull the cord around sharp corners. 5. DO NOT leave the cord near heated surfaces.

To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. If this occurs, immediately shut off power to the vacuum and remove the cord from the brushroll or nozzle.

NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap of the box. To order additional accessories, visit sharkaccessories.com.

This slim tool is great for cleaning in tight spaces, between couch cushions, and in hardto-reach areas. A longer crevice tool is available at sharkaccessories.com.

This versatile, slender 8 ^ { \prime \prime } tool removes pet hair from hard-to-reach spaces like corners, stairs, and between couch cushions.

Picks up pet hair, dust, and large debris from mattresses, couches, curtains, and other delicate upholstered fabrics.

Wide cleaning path helps remove pet hair, dust, and large debris from mattresses, couches, curtains, lampshades, and other delicate upholstered surfaces.

This brush dusts and cleans delicate surfaces. Great for use on fans, blinds, lampshades, and keyboards.

A single convertible tool for cleaning tough pet messes two ways: use the stiff bristle brush to clean stuck-on debris, or take off the bristles to reveal an upholstery tool perfect for removing stubborn pet hair and large piles of debris.

This brush features nylon fiber bristles specifically designed for removing fine dust and allergen particles from the most delicate surfaces.

The turbine brush loosens and removes pet hair and debris from carpets, and powerfully deep-cleans dander out of upholstery and other surfaces.

This flexible tube features a micro-duster crevice tool on the end for cleaning around delicate objects and in difficult-to-reach spots like car interiors and computer keyboards.

Clean under and behind hard-to-move appliances and furniture with this adjustable 3 6 ^ { \prime \prime } tool. Flip the extension piece over to clean the underside of appliances.

This removable clip attaches to your vacuum. The clip can store up to two accessories at a time while you clean.

• To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. If this occurs, immediately shut off power to the vacuum and remove the cord from the brushroll or nozzle.
Inspect power cord and plug for any damage before use. DO NOT use vacuum cleaner with a damaged cord or plug. Turn off all controls before plugging in or unplugging the vacuum cleaner. Store your vacuum cleaner with the power cord secured around the two cord hooks.

See Maintenance section for more information.

Empty the dust cup. Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinstalling them.

Clear any blockages in the nozzle, wand, handheld vacuum, or accessories. Vacuum is not picking up debris. No suction or light suction. See maintenance section for more information.

• If any string, hair, or carpet fibers remain wrapped around the brushroll after continued use, carefully clear them away.
Remove any blockages from the nozzle hose. Open the hose access latch on the bottom of the nozzle and lift up the hose. Clear blockages, then push the hose down and press the latch closed.
• If the problem persists, please call Customer Service.

Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges. Turn off the unit to disengage the brushroll. To restart, press the power button on the handle.

NOTE: Clean area rugs in Hard Floor mode or with accessories. See Available Accessories section.

If your vacuum overheats, the thermostat will automatically turn off the motor. Perform the following steps to restart:

1. Turn off the vacuum and unplug it. 2. Empty the dust cup and clean the filters. See Emptying the Dust Cup and Cleaning Filters sections. 3. Check for blockages in the wand, floor nozzle, handheld vacuum, inlet openings, and accessories. 4. Reassemble the entire vacuum and ensure all parts click into place. 5. Allow unit to cool for a minimum of 60 minutes. 6. Plug in vacuum and turn it on.

Due to the strong suction power of the vacuum, it is normal for the area around the filter exhaust to become warm during and after use. Turn off the vacuum and wait 10 minutes for it to cool down. If it still feels warm, clean the pre-motor and post-motor filters. See Maintenance section for filter cleaning instructions.

• Empty the dust cup after each use for optimal odor neutralization.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinstalling them.
• Check to make sure odor neutralizer cartridge is installed into the nozzle.
• Check the odor neutralizer dial on the nozzle to see which setting is enabled.
• If in Low to High setting and odor cartridge has been installed for 6 months or longer, consider replacing it.
• If the cartridge is still emitting a scent but you dislike it, consider turning the intensity down, or reinstall the dial in the nozzle without the cartridge.
• If the cartridge is not emitting a scent, consider replacing it.

• Turn off the vacuum and detach the floor nozzle. Find the Floor Detect sensor on the bottom of the nozzle and use a cotton swab to wipe away dirt and debris from the sensor and surrounding area.

For all other issues, please go to support.sharkclean.com or call Customer Service 1-800-798-7398.

The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.

SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of five (5) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:

1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to five (5) years from the original purchase date. 2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com. 2. Any unit that has been tampered with or used for commercial purposes. 3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters, not removing debris from the brushroll), or damage due to mishandling in transit. 4. Consequential and incidental damages. 5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja. 6. Products purchased, used, or operated outside North America.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call.

SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of \ 25.95$ (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.

This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

registeryourshark.com

Scan QR code using mobile device

Scan here or visit qr.sharkclean.com/odortech for more information

Model Number:

Date Code:

Date of Purchase:

(Keep receipt)

Store of Purchase:

Voltage: 120V~, 60Hz

Watts: 600W

1. Product Name: Odor Neutralizer Cartridge 2. Manufacturer: Shark Ninja 89 A Street Needham, MA 02494 3. Weight: 17.4g / 0.61oz 4. Ingredients: Solid SM composite polymer C17 ^ + fragrance SE 272235

Benefits of registering your product and creating an account:

• Get easier, faster product support and access to warranty information
• Access troubleshooting and product care instructions
• Be among the first to know about exclusive product promotions

TIP: The model number is on the rating label behind the dust cup.

TIP: The date code is on one of the prongs of the power cord plug.

This Owner’s Guide is designed to help you get a complete understanding of your new Shark POWERDETECT™ Corded Stick Vacuum with DuoClean Detect™, Self-Cleaning Brushroll, and Odor Neutralizer Technology.

SharkNinja Operating LLC

US: Needham, MA 02494

CAN: Ville St-Laurent, QC H4S 1A7

sharkclean.com

Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.

This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.