Roborock Qrevo S5V

• For use only with roborock EWFD24LRR docking station.
• The product must be switched off and the plug must be removed from socket outlet when not in use, before cleaning or maintaining the product.
• To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
• The docking station can only be used to charge the robotic vacuum cleaner equipped with a 14.4 V/5200 mAh (TYP) lithium-ion battery.

• Only use the product in accordance with the User Manual. Any loss or damage caused by improper use will be borne by the user.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not rinse the robot and the dock.
• Do not use the product to clean hard or sharp objects (such as decoration wastes, glass, and nails) to avoid scratching the robot, the dock or the floor.
• Make sure dustbin, washable filter, dust bag, side brush, mop cloths, main brushes and main brush cover are installed in place before cleaning.
• Do not sit or stand on the robot or dock.
• To prevent corrosion or damage, do not use any disinfectant and only use cleaning solution recommended by Roborock.
• Do not put any low objects (such as shoes, mats) near raised areas like stairs. Otherwise, the robot may fall down caused by malfunctional sensors.
• To prevent water damage, make sure that the floor where the robot operates is free of water.
• Do not operate the product in a room where an infant or child is sleeping.
• Before using the product, move sundries such as wires and any unstable, fragile, precious, or dangerous items from the floor to prevent them from being pulled by the robot and causing personal injury or property damage.
• Keep hair, loose clothing, fingers, and all body parts of people and pets away from seams, openings and moving parts of the product to avoid possible injury.
• Do not carry the robot using vertical bumper, top cover, side brush or bumper. Do not move the dock by lifting dock base, water tank handles or dust container cover.
• Place the dock on a hard, flat floor. Keep the dock, robot, and power cord away from fire and heat sources like a heating radiator. Avoid humid and narrow spaces or locations where the robot may be suspended in the air.
• This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.
• Do not dismantle, repair or modify the battery or charging dock.
• If the dock is placed in an area susceptible to thunderstorms or with unstable voltage, take protection measures.
• Do not use the product on high pile carpets. Product effectiveness may also be reduced on dark carpets.
• Do not place any object on top of the robot or dock, near the suction inlet of the dock, or cover them with any item (including dust-proof cover).
• Do not use this product on elevated surfaces without barriers such as the floor of a loft, an open-ended terrace, a slide, or top of furniture.
• Do not use the dock to pick up stones, paper scraps, or other objects that may block the air duct.
• Do not operate the product if it has been damaged in any way. Contact customer service for help.
• Always operate the device in well-ventilated areas to prevent overheating.
• Roborock disclaims all liability for indirect, punitive, incidental, or consequential damages resulting from the use, misuse, or inability to use this product. This disclaimer does not affect any statutory rights that may not be disclaimed under applicable law.
• To avoid burns, do not touch the drying air outlets.

• Do not wipe the charging contacts with wet cloth or wet hands.
• If the product is left unused for a long period, store it in a cool, dry place after having it fully charged, unplugged, and switched off. Recharge it at least every three months to avoid battery overdischarge.
• Do not use the product when the temperature is higher than 40°C (104° F ) or lower than 4°C (39° F ) , or if there is any liquid or sticky substance on the floor.
• Do not discard waste batteries. Leave them with a professional recycling organization.
• To transport the product, be sure to unplug the dock, switch off the robot, and empty water tanks. Use of the original packaging is advised.
• Be sure that the supply voltage meets the requirements listed on the dock.

~ – ALTERNATING CURRENT symbol [symbol IEC 60417-5032 (2009-02)] – DIRECT CURRENT symbol [symbol IEC 60417-5031 (2009-02)] – For indoor use only.

FCC/IC Statement

• Press and hold to turn the robot on or off
• Press to start cleaning

• White: Battery level \geq 1 5%
• Red: Battery level < 1 5%
• Breathing: Charging or starting up
• Flashing red quickly: Error

• Robot not on dock: Press to start docking / Press and hold to start spot cleaning
• Robot on dock: Press to start emptying / Press and hold to wash the mop cloths

Note: Press any button to pause a running robot.

A1-1—Reactive Tech Obstacle Avoidance Sensor

A2-1—Wall Sensor A2-2—Omnidirectional Wheel A2-3—Carpet Sensor A2-4—Side Brush A2-5—Main Brush Cover A2-6—Main Wheels A2-7—Main Brushes

A2-8—Main Brush Cover Latches A2-9—Mop Cloths A2-10—Cliff Sensors

A3-1—Vertical Bumper A3-2—LiDAR Sensor A3-3—WiFi Indicator Light

• Off: WiFi not connected
• Flashing slowly: Waiting for connection
• Flashing quickly: Connecting
• Steady: WiFi connected

A3-4—Reset Button A3-5—Dustbin A3-6—Charging Contacts A3-7—Communication Sensor A3-8—Air Outlets A3-9—Self-Filling Port A3-10—Automatic Lift and Rotate Mop Modules A3-11—Suction Inlet A3-12—Bumper

A4-1—Hook and Loop Pads

A4-2—Mop Axle

Note: Secure the mop cloths flat in place.

A6-1—Dustbin Latch

A6-2—Air Inlet

A6-3—Filter Latch

A6-4—Washable Filter

A6-5—Suction Inlet

A9-1—Water Tank Handle

A9-2—Water Tank Latch

A9-3—Dirty Water Tank

A9-4—Dust Container Cover

A9-5—Charging Contacts

A9-6—Robot Refill Port

A9-7—Suction Inlet

A9-8—Clean Water Tank

A9-9—Status Indicator Light

• Breathing: Emptying/Mop washing
• Red: Dock error
• Off: Powered off/Charging

A9-10—Drain Port A9-11—Drying Air Outlets A9-12—Dock Base A9-13—Filter A9-14—Dust Bag Slot A9-15—Dock Location Beacon A9-16—Clean Water Dispensers A9-17—Water Level Float A9-18—Cleaning Tray Filter A9-19—Cleaning Tray

To minimize disturbance, the status indicator light Note: will be off or dim in DND mode.

A10-1—Power Cord Storage Slot

A10-2—Power Port

A10-3—Cord Outlets

Note: Power cord can exit at either side.

B1-1—Tidy cords, hard or sharp objects (such as nails and glass), and loose items from the ground and move any unstable, fragile, precious, or dangerous items to prevent personal injury or property damage due to items becoming tangled in, struck by, or knocked over by the robot.

B1-2—When using the robot in a raised area (such as in a duplex apartment), always use a physical security barrier to prevent accidental falls that may result in personal injury or property damage.

• When using the robot for the first time, follow it throughout its whole cleaning route and watch for potential problems. The robot will be able to clean by itself in future uses.
• To prevent excessive buildup of dirt on the mop cloths, the first mopping cycle.

B2-1—Attach the dock base by pressing down both sides of the base and the connecting part in the middle firmly until you hear a click.

When moving the dock, secure the water tanks toNote: prevent it from falling off.

B2-2—Connect the power cord to the back of the dock, and keep the excess cord inside the storage slot.

Note: Power cord can exit at either side.

B2-3—Align and install the mop axles into the robot in place until you hear a click.

Place the dock on a hard, flat floor (wood/tile/concrete etc.), flat against a wall, and reserve a space of at least 0.9 m (2.95 ft) in height, 0.4 m (1.31 ft) in width and 1.2 m (3.94 ft) in depth. Make sure that the location has good WiFi coverage for a better experience with the mobile app. Plug in and make sure that the status indicator light is on.

B3-1—More than 1 . 2 m (3.94 ft) B3-2—More than 0.9 m (2.95 ft) B3-3—More than 0.4 m (1.31 ft)

• If the power cord hangs vertically to the ground, it may be caught by the robot, causing the dock to be the storage slot.
• The status indicator light is on when the dock is powered on, and off when the robot is charging.
• The status indicator light turns red if an error occurs.
• Place the dock on a hard, flat floor away from fire, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may cause the dock to tilt and cause docking and departing problems.
• Keep the dock away from direct sunlight or anything that may block the dock location beacon, otherwise the robot may fail to return to the dock.
• Do not use the dock without clean water tank, dirty water tank, dust container cover, disposable dust bag, cleaning tray filter, or cleaning tray.
• Maintain the dock according to the Routine Maintenance. Do not clean the dock power cord or charging contacts with a wet cloth or tissue.
• All docks are subject to water-based tests before leaving the factory. It is normal that a small amount of water remains in the waterway of the dock.

Press and hold to power on the robot. Wait until the power indicator light is steady, and then place the robot in front of the dock. Make sure that the dock is plugged in. Then, press and the robot will automatically return to the dock for charging. The robot is equipped with a built-in high-performance lithiumion rechargeable battery pack. To maintain battery performance, keep the robot charged.

B4-1—Dock status indicator light off, robot power indicator light breathing: Charging

The robot may not be turned on when the batteryNote: is low. In this case, place the robot on the dock for charging.

Search for “Roborock” in the App Store or Google Play or scan the QR code to download and install the app.

a. Open the top cover and find the WiFi indicator light. b. Press and hold and simultaneously until you hear the “Resetting WiFi” voice message. The reset is complete when the WiFi indicator light flashes slowly. The robot will then wait for a connection.

If you cannot connect to the robot due to yourNote:

Open the Roborock app, tap the “Add Device” or " + " button and add your device following the in-app guide.

• The actual process may vary due to ongoing app updates. Follow the guide provided in the app.
• Only 2.4 GHz WiFi is supported.
• If the robot waits more than 30 minutes for a connection, WiFi will be automatically disabled. If you want to reconnect, reset the WiFi before proceeding.

Lift the clean water tank, open its lid, and then fill it with tap water. After filling, close the lid, lock the latch, and then put the clean water tank back to the dock.

• To prevent damage, do not use any disinfectant and only use cleaning solution recommended by Roborock.
• Do not add too much cleaning solution to prevent the robot from working improperly due to slipping.
• To avoid deformation, only use cold water.
• If any water stains remain on the outside of the water tank, wipe them with a soft, dry cloth before reinstalling the tank.

Press and hold to turn on the robot. The power indicator light will come on, and the robot will be on standby.

Press and hold to turn off the robot and complete the cleaning cycle.

The robot cannot be turned off when it is beingNote: charged.

Press to start cleaning. The robot will plan its cleaning route and in each room, it firstly draws out edges and then fills the room in a zigzag pattern. In so doing, the robot cleans all rooms one by one, thoroughly and efficiently.

start the robot from the dock and do not move the dock during cleaning.

• Cleaning cannot start if the battery level is too low. Allow the robot to charge before starting a cleanup.
• Before cleaning, tidy cords (including the power cord of the dock) and valuables from the floor. Loose items may be dragged by the robot, resulting in the disconnection of electrical appliances or damage of cords and property.
• If cleaning is completed in less than 10 minutes, the
• If the battery runs low during a cleaning cycle, the robot will automatically return to the dock. After charging, the robot will resume where it left off.
• The robot will retract mop cloth mounts to clean the carpet. You can also set the carpet as a no-go zone in the app to avoid it.
• Before starting each cleaning task, make sure that the mop cloths have been properly installed.

Press and hold to start spot cleaning.

Cleaning range: The robot cleans a 1.5 m (4.9 ft) × 1 . 5 m (4.9 ft) square area centered on itself.

After spot cleaning, the robot will automaticallyNote: return to the starting point and be on standby.

When the robot is running, press any button to pause it, press to resume cleaning. Press on a paused robot to send it back to the dock.

Placing a paused robot on the dock manually willNote: end the current cleanup.

If the robot is paused for over 10 minutes, it will go to sleep, and the power indicator light will flash every few seconds. Press any button to wake the robot up.

• The robot will not go to sleep when it is charging.
• The robot will automatically shut down if left sleep for more than 12 hours.

The default Do Not Disturb (DND) period is from 22:00 to 08:00. You can use the app to disable the DND mode or modify the DND period, or set whether to enable auto topup, emptying and drying, to dim indicator lights, or lower the volume of the voice message during the DND period.

During cleaning, the robot automatically determines when it should return to the dock for mop washing and water tank refilling to maximize its mopping

performance. To manually start washing, tap the corresponding button in the app. Press any button to stop washing.

• To ensure the robot automatically washes the mop cloths, start it from the dock and avoid moving the dock during cleaning.
• Mop wash frequency and mode can be modified in the app.

After cleaning, the robot will return to the dock and auto-emptying will begin as needed. To manually start emptying, press on the docked robot or tap the corresponding button in the app. Press any button to stop emptying.

• When emptying has been left unused for a long period, empty the dustbin manually and make sure the air inlet is clear for optimal emptying performance.
• Auto-emptying can be disabled in the app.
• Avoid frequent manual emptying.
• Do not use without dust container cover or disposable dust bag installed in place.

After mop washing or after cleaning, drying will begin as needed. To manually start or stop drying, tap the corresponding button in the app.

• Drying duration can be modified in the app.
• Auto-drying can be disabled in the app.
• Stay away from the drying air outlets during drying.

After cleaning, the robot will automatically return to the dock to charge. Press to send the paused robot back to the dock. The power indicator light will breathe during robot charging.

If the robot fails to find the dock, it will automaticallyNote: return to its starting position. Place the robot on the dock manually to recharge.

If an error occurs, the power indicator light will flash red or status indicator light will be steady red. A pop-up notification will appear in the app and a voice alert may sound.

• The robot will go to sleep automatically if left in a malfunctioning state for over 10 minutes.
• Placing a malfunctioning robot on the dock manually will end the current cleanup.

If the robot does not respond when a button is pressed or cannot be turned off, reset the system by pressing the Reset button.

After resetting the system, existing settings suchNote: as scheduled cleaning and WiFi will be restored to factory settings.

If the robot does not function properly after a system reset, power it on. Press and hold and at the same time, press the Reset button until you hear the “Restoring factory

settings. This will take about 5 minutes.” voice message. The robot will then be restored to factory settings.

• The product must be switched off and the plug must be removed from socket outlet before cleaning or maintaining the product.
• The frequency of replacement may vary with the actual situation. If abnormal wear occurs, replace the parts immediately.

* Clean every 2 weeks and replace every 6-12 months.

D1-1—Main Brush Cover D1-2—Main Brush Cover Latches D1-3—Main Brushes D1-4—Main Brush Bearing D1-5—Turn over the robot and press the two latches inwards to remove the main brush cover. D1-6—Lift the main brushes and pull them out, remove bearings and remove any entangled hair or dirt at both ends of the main brushes and bearings. D1-7—Reinstall the main brush bearings. And then, reinstall the main brushes and make sure the color of the main brush, main brush bearing and the arrow on the robot match.

D1-8—Reinstall the main brush cover. Make sure its four teeth are fully seated in the slots, and press the main brush cover until you hear it lock with a click.

• It is recommended to wipe the main brushes with a wet cloth. If the main brushes are wet, air-dry them away from direct sunlight.
• Do not use corrosive cleaning fluid or disinfectant to clean the main brushes.

* Clean monthly and replace every 3-6 months. D2-1—Turn over the robot, unscrew the side brush, then remove and clean it. D2-2—Align the central groove with the raised position on the robot and tighten the screw to reinstall the side brush.

* Clean as required.

D3-1—Use a tool, such as a small screwdriver, to pry out the axle slowly and take out the wheel.

Note: The omnidirectional wheel bracket cannot be removed.

D3-2—Rinse the wheel and the axle with water to remove any hair and dirt. Air-dry, reinstall, and press the wheel and axle back in place.

Clean as required.

Clean the main wheels with a soft, dry cloth.

* Clean as required.

D5-1—Open the top cover of the robot and press the dustbin latch to take out the dustbin. D5-2—Remove the washable filter and empty the dustbin. D5-3—Fill the dustbin with clean water and reinstall the washable filter. Gently shake the dustbin, and then pour out the dirty water.

To prevent blockage, only use clean water withoutNote: any cleaning liquid.

D5-4—Allow at least 24 hours for the dustbin and washable filter to dry thoroughly before reinstalling them.

* Clean every 2 weeks and replace every 6-12 months. D6-1—Remove the filter. D6-2—Rinse the filter repeatedly and tap it to remove as much dirt as possible. Do not touch the surface of the filter with hands,Note: brushes, or sharp objects to avoid potential damage. D6-3—Allow at least 24 hours for the filter to dry thoroughly before reinstalling it.

* Clean as required and replace every 1-3 months.

D7-1—Remove the mop cloths from the mop cloth mounts. Clean the mop cloths and air-dry them.

A dirty mop cloth will affect the mopping performance.Note: Clean it before use.

D7-2—Stick the mop cloths on the mounts flat in place.

* Clean as required.

Use a soft, dry cloth to wipe and clean all sensors, including:

D8-1—Reactive Tech Obstacle Avoidance Sensor D8-2—Wall Sensor D8-3—Communication Sensor D8-4—Carpet Sensor D8-5—Cliff Sensors

To move the dock, grip the cord storage slot on the back with one hand and the inner side of the front board with the other hand. Do not lift the dock base, water tank handles, or dust container cover directly to prevent the dock from falling off.

Clean as required.

Open the dirty water tank lid and pour out the dirty water. Fill the tank with clean water, close the lid, lock the latch, and shake. Pour out the dirty water. Lock the lid and reinstall the tank.

• To avoid deformation, only use cold water.
• If any water stains remain on the outside of the water tank, wipe them with a soft, dry cloth before reinstalling the tank.

* Clean as required.

Use a soft, dry cloth to wipe the charging contacts on the robot and the dock.

* Replace as required.

D12-1—Remove the dust container cover.

To prevent the dust container cover from fallingNote: and hitting the robot, remove the cover with both hands, one on each side.

D12-2—Remove the disposable dust bag and discard it.

• The dust bag handle seals the bag on removal to prevent leakage.
• Always install a dust bag before putting back the dust container cover to avoid auto-emptying without the bag. You can also disable auto-emptying in the app.

D12-3—Clean the filter with a dry cloth, insert a new disposable dust bag into the slot all the way in, and spread it evenly.

Make sure the disposable dust bag is properlyNote: installed to avoid waste escaping and damaging the dock.

D12-4—Reinstall the dust container cover in place to make sure the dust container is securely sealed.

* Clean as required.

D13-1—Remove the cleaning tray.

D13-2—Rinse the cleaning tray and the filter with water. D13-3—Reinstall the cleaning tray.

The serial number is on a sticker on the undersideNote: of the robot.

The following information applies only when disposing of the robot and should not be followed for day-to-day operations.

The chemical substances contained in the built-in lithium-ion battery of this product can cause environmental pollution. Remove the battery before disposing of this product and hand it to a professional battery recycling facility for centralized disposal.

How to remove the battery:

1. Operate the robot without connecting to the dock until it runs out of battery. 2. Turn off the robot. 3. Unscrew the battery cover. 4. Remove the battery cover. 5. Press the latch to pull out the battery connector and remove the battery.

• Before removing the battery, make sure it is fully
• Remove the entire battery pack. Avoid damaging the battery pack casing to avoid short-circuits or leakage of hazardous substances.
• In the event of accidental contact with battery fluid, rinse thoroughly with water and seek immediate medical care.

Common Issues

Issue	Solution
Unable to auto-empty	Auto-emptying is disabled. Check in-app settings. The dust container cover is not installed. Check and install. Auto-emptying will not be triggered if the robot returns to the dock without cleaning. The robot will not auto-empty after returning to the dock in DND mode. Adjust the cleaning time or DND period, or start emptying manually. Auto-emptying will not be triggered if the robot is moved to the dock manually. Start emptying manually.
Unable to wash the mop cloths	The mop cloths will not be washed if not used. If the robot does not start from the dock or no dock is found on the app map, it will not return to the dock for mop washing. Check clean water tank placement or refill the tank as required. Check dirty water tank placement or empty the tank as required. Check that the cleaning tray and cleaning tray filter have been properly installed.
Unable to extend the mop cloth	Check that the FlexiArm Design Extended Mopping feature is enabled in the app. The mop cloth will only extend along walls and certain obstacles. Check if the mop extension structure is stuck.