Petkit PuraMax 2

*Please ensure that all accessories are present before installation and use.

Main Unit

* The installation and disassembly method is the same as the standard litter sier. See 5.2- and 5.5- for details.

* Only included in the premium package.

Magnetic Cat Litter Remover Power Adapter Trash Bag Pet Odor Eliminator N50 2.0 User Manual

* Note: In order to provide better products, we will regularly improve the product. If the product picture is slightly dierent from the actual product, the actual product shall prevail.

* Pet odor eliminator N50 2.0 below is referred to as N50. * High performance cat litter pad MAX below is referred to as cat litter pad. * The standard litter sifter is suitable for tofu cat litter and mixed cat litter; The honeycomb fine litter sifter is suitable for mineral cat litter.

❶ Slide the latch to the right and pull out the waste bin. Remove the lid of the waste bin to take out all accessories.

Unlocked

❷ Install the trash bag in the waste bin, ensuring that the trash bag lies flat at the bottom, then put the lid on.

Note: The two sides of the lid need to clamp the trash bag. (as shown in Fig. 1)

❸ Put the N50 in and press firmly.

❹ Install the waste bin back into the main unit and lock the latch.

❺ Take out the power adapter, insert it into the power port on the back of the main unit, then plug it in.

Note: Do not use large particles of cat litter larger than 1.2cm in length and 3mm in diameter.

❶ After the device is powered on, press the menu button \circledast to switch to “Maintenance Mode” and press the OK button ∙× to execute, and then the cylinder begins to rotate.

❷ When the cylinder stops with the opening facing up, pour in the cat litter. Press the OK button ° κ to exit “Maintenance Mode”.

❸ Double-press the OK button ∙ κ and the device will automatically level off the cat litter.

Caution: The amount of cat litter doesn’t exceed the MAX line of the cat litter pad.

❶ Press the menu button \circledast to switch functions, and press the OK button ° κ to execute.

Turn on or turn o

Switch functions, and the screen will show the function.

Execute the selected function.

OK

Use it when adding cat litter or cleaning the device.

Reset the cylinder to the initial position.

Start automatic scooping.

The device is connecting to the Wi-Fi (use it when binding the app).

Level the cat litter in the cylinder (use it after adding cat litter).

The air purifier begins to deodorize.

* To perform this function, the installation of PETKIT air purifier is required.

There will be scrolling text at the bottom of the screen.

❶ Download and install the PETKIT App

Download the PETKIT App from the App Store or Google Play.

Available on the App Store

Get it on Google play

❷ Add the device

Open the app, click s _ + s in the top right corner and choose

“PETKIT PURA MAX 2 SELF-CLEANING CAT LITTER BOX”.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

Press the menu button on the device to switch to “Configure network”, then press the OK button to execute this function. The screen will display “Connecting...”, and the app will start connecting to the device. Please wait until the configuration is successful.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

To ensure your pet’s safety and use this product properly, please read the instructions carefully after connecting to the app for the first time.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

Enter the device’s home page and check its working status, pet toilet times, waste bin status, etc.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

Clean now: Click it to clean the cat litter.

Maintenance mode: Click it and the cylinder will rotate until its opening faces up, making it convenient to add cat litter or clean the device.

Empty cat litter: Aer installing the magnetic cat litter remover, click it to empty the remaining cat litter in the cylinder.

Smart settings: Set up cleaning mode and safety mode.

Deodorize: Click it to deodorize.

* To perform this function, it is required to install PETKIT AIR PURIFIER SMART SPRAY.

Light on: Click it to turn on the light in order to check the internal condition of the cylinder.

* To perform this function, it is required to install PETKIT AIR PURIFIER SMART SPRAY.

Click “Binding AIR PURIFIER” on the device’s home page.

❶ Deodorize: Aer the pet leaves the litter box, the AIR PURIFIER will automatically spray to keep air fresh. ❷ Light on: Turn on the light in the app to check the internal condition of the cylinder.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

Turn on this mode if you have kittens or pregnant cats at home. When this mode is on, auto-cleaning and periodical cleaning will be disabled. You can click “Clean now” to clean the cat litter.

When this function is turned on, the device will not stop working even if it detects a cat approaching, which can reduce the possibility of a cat entering and its secretions leaking into the bottom of the device.

* When this function is turned off, the device will stop working if it detects a cat approaching. If the cylinder opening is facing downwards at the moment, there is a possibility of a cat entering and the leakage of toilet secretions into the bottom of the device, making it hard to clean.

Note: The actual app interface may dier from the image shown due to continuous soware upgrades; the actual interface shall prevail.

For the cat’s health, it is suggested to regularly clean and replace these parts.

Caution: Before operation, please make sure the device is powered o.

* Avoid cleaning with alcohol, disinfectant, bleach, non-neutral detergent, etc.

❶ Pinch the raised part in the middle of the magnetic cat litter remover and align the three grooves on it with the corresponding holes on the litter sier. Once you hear a "click" sound, the installation is successful.

❷ Click “Empty litter” on the app, and then empty the cat litter in the cylinder according to the guide. \otimes Aer use, pinch the raised part on the le and pull out the magnetic cat litter remover.

❶ Rotate counterclockwise to remove the side cover.

❷ Press the middle of the litter sier until it is bent and separates from the le buckle, then remove the litter sier.

❸ Pinch the handle of the cat litter pad to pull out the cat litter pad.

❶ Remove the magnetic side cover upward.

❷ Unlock the buckle.

❸ Remove the cylinder upward.

Caution: The main unit is strictly prohibited from rinsing and soaking. It can only be wiped, otherwise, the device will be damaged.

❶ Clean every corner of the cylinder with a brush and rinse it.

❷ Scrub the litter sifter with a brush and rinse it off. Wipe the cat litter pad with a wet cloth.

Caution: Do not scrub vigorously to avoid damaging the coating of the cat litter pad. Avoid cleaning with non-neutral detergents such as alcohol, disinfectant, zbleach, etc.

❸ Wipe the base with a damp paper towel to keep the sensor clean.

proximity sensor

Caution: Install all parts only when they are completely dry. ❶ Put the cylinder on the base, lock the buckle, and make sure the buckle is fastened.

❷ Hold the cat litter pad, insert the upper part of it into the groove, and then insert the bottom of it into the groove (align with the arrows).

❸ Press gently and release the litter pad; its two sides will be automatically inserted into the groove.

Caution: Before use, make sure that the green edge of the cat litter pad is fully stuck into the groove and that the arrows on both ends are aligned with the direction indicated.

If the green edge is not visible, the installation is successful.

❹ Insert one side of the litter sier into point A in the cylinder.

❺ Grasp the litter sier and press it until it is bent.

❻ Insert the other side of the litter sier into point B in the cylinder.

❼ Please check: If the litter sier can be shaken back and forth, the installation is successful. ❽ Install the side cover and rotate it clockwise, then install the magnetic side cover.

• Thank you for choosing the PETKIT PURA MAX 2 SELF-CLEANING CAT LITTER BOX.
• Please read the user manual carefully before installing and using the product. Any installation or usage indicates that you have read and accepted the safety guide below.
• PETKIT is not responsible for or legally liable for any accidents or injuries resulting from the improper use of the product.
• PETKIT reserves the right to interpretation and revision.

* Failure to follow the safety guides below may result in product malfunction or other unforeseen losses.

• Please install and use the product according to the user manual.
• Cats younger than six months are not recommended to use this product. Cats weighing less than \mathbf { 1 . 5 } k g are not recommended to use this product.
• Do not place the device in a high-temperature or high-humidity environment.
• The product is for indoor use only. Please avoid direct sunlight exposure and keep it away from the source of flame.
• Although the device is powered by a low voltage, electric leakage may occur if the pet bites the power cord. Please guide your pets to use the product properly.
• Only use the original adapter to avoid device damage or safety hazards.
• Place the device on a hard, flat surface and avoid touching the wall.
• Do not tilt the device to avoid security risks.
• Do not immerse or soak the bottom of the device in water.
• There are weight sensors at the bottom of the device. Please handle it gently.
• Please unplug it if the device is not used for an extended period.
• Children should use this product under the supervision and guidance of adults.
• Repairs should only be performed with professionals’ guidance to avoid accidental damage.
• It is prohibited to place objects on the top of the device or press the device’s top to avoid affecting the normal operation of the device.
• Before leaving for an extended period, please ensure that there is suicient cat litter in the litter box and space in the waste drawer.
• If you have any problems with the product, please contact our customer service for assistance.

The European directive 2012 / 19 / CE on Waste Electrical and Electronic Equipment(WEEE), requires that old household electrical appliances must not be disposed in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials theycontain and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation,that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and ； (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

#

Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitationestautorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.