NARWAL Freo X10 Pro Robot Vacuum and Mop Combo

Main parts

Robot × 1

(Dust collection box × 1, roller brush × 1 installed)

Multifunctional dock × 1

(Including clean base × 1, clean water tank × 1 and dirty water tank × 1)

Anti-tangling side brush × 1 Power cord × 1 Dust Bag ×1

Replaceable cleaning filter × 1

Robot buons

Multifunctional dock buon

Robot indicators

Multifunctional dock indicators

Press the side brush firmly into the card slot and install it in place with a click.

Installed properly Not installed properly

• Remove the paper trays that fix the robot inside the dock.
•Take out the cleaning tray, clip the replaceable filter into the slot of the tray and press it down to install it in place.
• Put the cleaning base with cleaning filter installed back to the dock.

•Remove the dock front cover. •Insert the dust bag into the slot in the marked direction until it hits the boom. •Install the dock front panel in proper place.

• Open the clean water tank and fill it with clean water.
• Please fasten the upper lid of the water tank and put it back into the Multifunctional dock.

MAX water level mark

• Lift the top cover sticker to open the robot top cover and remove the anti-collision foam.
• Close the robot's top cover.

• Plug in the power cord in the back of the dock to connect the power.
• Leave an open space of at least 0.45 meter long in front of the dock for the robot to enter and leave the dock. Tips: DO NOT put the dock close to a heat source.

Add a floor cleaning tablet to the clean water tank. Note: Cleaning Tablet should be purchased separately.

Push the robot into the dock with side brushes facing outward. The dock will beep once to indicate that charging is successful and the robot will turn itself on and prompt a voice message.

Download the Narwal App and follow the instructions for connecting and binding the robot. Note:In the App device page, tap "Seings" > "Device" and then press hold the "Restart Robot" for 10s to turn on/o
the power-saving mode.

_The power-saving mode is only available in North America.

Before using the robot, please make sure you have finished the installation and multifunctional dock setup in Chapter 2.

A. Put away the cluer on the floor, e.g. scaered cables, rags, slippers, clothes, and books.slippers, clothes, and books.

B. Open the doors of the rooms to be cleaned and arrange the furniture to leave as much space as possible for cleaning.

C. Leave other doors closed and install the fence to prevent the robot from entering elevated or low areas.

E. DO NOT stand in front of the robot, on the threshold, or in narrow aisles to avoid omission.

D. The maximum obstacle crossing height is 20mm and the robot cannot enter rooms with a threshold height of over 20mm. You can purchase Narwal Threshold Ramp to help the robot climb over obstacles.

Before cleaning a new home, the robot needs to explore the home and create a map. Before first-time cleaning, you can trigger mapping by short pressing the button on the dock or tapping [Start Mapping] in the App.

Note:

1. Once a map is created, it can be edited in the App. 2. Do not move the dock after mapping finished, otherwise you need to rebuild the map. If there is a change in the location of large pieces of furniture, it is recommended to rebuild the map.

The product comes with four built-in cleaning modes: Vacuum, Mop, Vacuum and Mop, and Vacuum then Mop. You can select and adjust parameters like cleaning cycles, suction, and mop humidity for each mode in the App.

The Freo Mind is an intelligent cleaning assistant. When Freo Mind is turned on, the robot will intelligently adjust cleaning parameters, without needing manual seings.

You can select whether to activate Freo Mode when starting a cleaning task in the App.

You can start the robot for cleaning in three ways:

• Tap \odot [Start Cleaning] in the App;
• Short press the [Start/Stop] button on the robot to start cleaning. The robot will activate the Vacuum Mode by default;
• Short press the button on the dock to start cleaning. The robot will activate the Vacuum and Mop Mode by default;

Note: You can adjust the cleaning mode and set more cleaning parameters in the App.

You can pause/resume the current task in three ways:

• Tap \cdot [Pause]/ [Resume] in the App;
• Short press the [Start/Stop] buon
• Short press the dock buon.

When vacuuming task started, solid waste in the robot dust box will be automatically vaccumed to the dust bag in the dock. You can also tap dust collection in the App to start dust collection manually.

If the robot is set for multiple mopping runs or the area for cleaning is large, the robot will automatically return to the dock for mop washing.

The number of mopping runs and return frequency can be modified in the App before cleaning starts, and the modification during the current cleaning task will take e
ect during the next task.

You can also have the Multifunctional dock wash the mop:

• Tap [Mop Washing] in the App;
• Double-click the dock [mop].

Note: Please DO NOT pull the robot out the dock during mop cleaning process so as to avoid component damage.

The robot will navigate itself back to the dock when cleaning ends. You can view the current cleaning report in the App. You can manually end the task in the following three ways:

• Press 2s \cdot [Task End] in App];
• Short press robot [Recall];
• Long press the dock buon for 2s.

After the last mopping run, the robot will return to the dock for mop washing and drying. The drying time can be modified in the App. You can also start mop washing and drying manually in the following way:

• Tap [Mop Washing & Drying] in the App;