eufy L60

b onBumper \pmb { \varrho } 0° Lidar Navigation Cleaning Start / Pause button \pmb { \Theta } orRecharge Button \bullet st Box360° Lidar Navigation Sensor \bullet st Box Release BCharging Pins - erBack Flow Prevention Flap 7 Filter 8 Dust Box ❾ Dust Box Release Buttons ( \times 2 )

1 Side Brush \pmb { \varrho } Swivel Wheel \pmb { \Theta } Anti-drop Sensors (×3) Wheels (×2) \bullet Rolling Brush 6 Brush Guard

Charging Station

❶ Power Adapter 2 Charging Pins

1.3 Buttons Control

You can see the status of RoboVac from the LED indicators.

1. Remove the foam blocks beside the bumper and all the protective films before use.

2. Peel off the protective film around and sticker beneath the Charging Station, and install it in a location that RoboVac can easily access. It is recommended to place it against a wall and on a hard, level surface rather than on rugs or carpets.

It is recommended to remove objects within 1.6 ft / 0.5 m to the left and right sides and within 4.9 ft / 1.5 m of the front of the Charging Station. If you cannot remove the objects, move RoboVac to a new place and check whether RoboVac can return to the Charging Station normally; if not, contact us at support@eufy.com for suggestions.

• Do not place the Charging Station near the edge of staircase.

3. Attach RoboVac to the Charging Station, then press and hold the cleaning start/pause button for 3 seconds to turn it on.

• Fully charge RoboVac before use. The LED indicator on RoboVac will be solid white when fully charged.
• After powering on RoboVac, please wait for 20 seconds after the startup music sounds before proceeding to the next operation.

RoboVac returns to the Charging Station automatically to recharge when:

• RoboVac has finished cleaning;
• Cleaning is not complete and the battery level becomes low; once recharged to 80% battery capacity, RoboVac will resume and finish the remaining cleaning.

Do not move the Charging Station during cleaning. Do not unplug the Charging Station, otherwise RoboVac may fail to return for recharge.

To enjoy all the available features, it is recommended to control your RoboVac via the app.

• Your smartphone or tablet is running iOS 11 (or above) or Android 8.0 (or above).
• The 2.4GHz band or 5.0GHz band wireless signal is enabled on your wireless router.

1. Download the app from the App Store (iOS devices) or Google Play (Android devices), or by scanning the QR code. 2. Open the app and create a user account. 3. Tap the “+” icon to add RoboVac to your App account. 4. Follow the instructions in the app to set up the Wi-Fi connection.

• After connecting successfully, you can control RoboVac via the app.
• With the app, you can select cleaning modes, select cleaning at your desired suction power, schedule cleaning, view the system status, set up “No-Go” zones, receive notifications, and access additional features.
• If RoboVac gets stuck in any space, tap Find My Robot in the app to find the device.

If you bump into issues when connecting your RoboVac to the app, you can try to reset the Wi-Fi connection. To reset the Wi-Fi connection, press and hold the two buttons simultaneously for 3 seconds until you hear a voice prompt.

You will hear a voice prompt when the Wi-Fi connection has been reset, and the LED indicators on RoboVac will quickly flash red. Now you can follow the Wi-Fi instructions in the app to set up the Wi-Fi connection.

For a deep dive into how to use the Mapping feature, click the link below to explore more: https://support. eufy.com/s/product/a085g00000GiufvAAB/eufy-clean-l60-ses

Quick mapping helps RoboVac to learn the correct learning path and the environment of your home easily. A floor plan will be built after cleaning.

To create a complete floor plan:

1. Open your doors so that RoboVac can map each room. You can also block off certain areas that you don't want RoboVac to enter, which can improve the success rate of Quick Mapping. 2.Remove any objects that may be in the way or that might entangle RoboVac.

• Do not remove the Charging Station after a floor plan is created.

With the app, you can set up a “No-Go Zone” or “Virtual Wall” as a restricted area. This eliminates the need to use physical barriers, including boundary strips. This feature is only designed for dividing the cleaning zones, not for isolating hazardous areas.

• No-Go Zone: RoboVac will not enter the zone to vacuum.
• Virtual Wall: RoboVac will not cross the virtual wall.
• To set a virtual wall, RoboVac must initially perform a cleaning run to create a floor plan.
• Although a virtual wall is set, RoboVac may still enter the restricted zone due to repositioning failure or abnormal sensors.
• Moving the device or changing the environment may lose the virtual wall and cause the mapping to fail and rebuild.

With the app, you can schedule RoboVac to start cleaning at a particular time.

• You can set the time and customize cleaning schedules from Sunday to Saturday on the app. This function is only available on the app.

You can select multiple cleaning modes via the app.

Press the cleaning start/pause button to start cleaning in Auto Mode.

After startup, RoboVac moves from the Charging Station and automatically determines its cleaning route, cleaning the edges first and following a Z-shaped cleaning path. When cleaning is finished, RoboVac automatically returns to the Charging Station.

• To pause cleaning, press the cleaning start/pause button again.

• By default, RoboVac starts in Auto-cleaning Mode when it is turned on.

In this mode, you can set up a cleaning zone and customize its size in the app, RoboVac will clean the selected zone only.

In this mode, your house is automatically divided into several rooms for cleaning in the app. You can also customize your room settings in the app. RoboVac will clean the selected rooms only and return to the Charging Station after cleaning.

• Enable Room Cleaning only after RoboVac has created the map.
• It is recommended that RoboVac moves from the Charging Station to start room cleaning.

In the app, select a suction power level according to your needs: Quiet, Standard (Default), Turbo, and Max.

• When RoboVac starts cleaning next time, it will clean according to the suction power level you previously selected.

In the app, you can also select the BoostIQ™ feature according to your needs. RoboVac will automatically increase suction power if it detects that stronger power is needed to ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-to-sweep messes, which will reduce the total cleaning time but increase the noise level. If the vacuuming noise caused by BoostIQ™ disturbs you, you can disable this feature.

Amazon Alexa or the Google Assistant are smart voice control devices that enable you to control RoboVac with your voice.

• RoboVac is attached to the Charging Station to ensure there is enough power.
• RoboVac is connected with the app.
• You have an Amazon Alexa-enabled device (i.e. Amazon Echo, Echo Dot, Amazon Tap, Echo Show, or Echo Spot) or a device enabled with the Google Assistant (i.e. Google Home, Google Home Mini). These devices are sold separately.
• The Amazon Alexa app or Google Home app is already installed on your smart device, and you have created an account.

1. Open the app and find “Smart Integrations” in the top left. 2.Follow the on-screen instructions to complete the setup.

Prior to cleaning and maintaining, power off the device and unplug the power adapter. Any other servicing should be performed by an authorized service representative.

For optimal performance, follow the instructions below to clean and maintain RoboVac regularly. The cleaning and replacement frequency will depend on your RoboVac usage habits.

Click this link to shop for accessories: https://uk.eufy.com/collections/ap-accessory?ref=navimenu_2_5_ copy

\textcircled{1} Press the release buttons on both sides to detach the dust box from RoboVac. \textcircled{2} Open the lid of the dust box. \textcircled{3} Empty the dust box. \textcircled{4} Take out the filter. \textcircled{5} Dust off the remains on the filter.

\textcircled{6} Clean the filter with water. \textcircled{7} Air dry the filter before next use. \textcircled{8} Place the filter back to the dust box. \textcircled{9} Close the dust box. \textcircled{10} Reinstall the dust box onto RoboVac.

❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽ ❾ ❿

• When reinstalling the dust box, make sure you hear two clicks on both sides to confirm the dust box has been fixed in place.
• Do not remove the backflow prevention flap to ensure that debris does not spill out of the dust box during the cleaning process or when pulling out the dust box.

\textcircled{1} Turn over the main unit, push the release tabs with both hands to unlock the brush guard. \textcircled{2} Take out the rolling brush. Clean the hair entangled on the rolling brush and debris with a scissor or cleaning tool. \textcircled{3} Wash the rolling brush and brush guard with water. \textcircled{4} Air dry the rolling brush and brush guard before next use. \textcircled{5} Reinstall the rolling brush by inserting the fixed protruding end first. \textcircled{6} Push back the brush guard until you hear a click.

❶ ❹ 2 ❺ ❸ ❻

\textcircled{1} Remove the side brush with a screwdriver. \textcircled{2} Carefully unwind and pull off any hair or substances that are wrapped between the main unit and the side brush. \textcircled{3} Clean the side brush with water.

\textcircled{4} Air dry the side brush before next use. \textcircled{5} Reinstall the side brush on the machine.

❶ ❷ ❸ ❹ ❺

To maintain the best performance, clean the sensors and charging pins regularly.

• Dust off the sensors and charging pins using a cloth or cleaning brush.

Here are just a few preliminary suggestions. If your problem persists or if you need further troubleshooting information, please visit https://support.eufy.com, go to the app, or contact support@eufy.com for help.

Hereby, Anker Innovations Limited declares that this device is in compliance with The Product Security and Telecommunications Infrastructure (Security Requirements for Relevant Connectable Products) Regulations 2023. For the Statement of Compliance, visit the website: https://www.eufy.com/uk/psti-related.

a.the equipment does not have a standby mode or other equivalent state in terms of energy efficiency requirements, power management function or the ability to deactivate wireless network connections mode; b.the power consumption of the equipment is likely to be higher than other equipment models meeting these functional requirements.

1. Power consumption in standby mode: ≤ 0.5 W 2. Power consumption in standby mode with Display: ≤ 0.8 W 3. Power consumption in networked standby mode: ≤ 2 W 4. Power management: ≤ 20 min

By default, network configuration is performed via BLE (Bluetooth Low Energy) through the mobile app. If BLE configuration fails, an option will appear to try alternative configuration methods (AP mode).

Trigger Condition:

Press the device’s reset button to enable BLE network configuration.

Status Description:

When the device is not yet connected to a network, it will automatically start BLE broadcasting and activate BLE services to provide Bluetooth network configuration functionality.

Trigger Condition:

Press the device’s reset button to enter the AP configuration window.

Configuration Window Definition:

The configuration window lasts for 30 minutes after pressing the reset button. The window will end either after 30 minutes or once a network configuration request is triggered during this period.

Behavior During Configuration Window:

The device will broadcast an open (no password) and visible AP hotspot.

The hotspot name (SSID) and password will be changed after the configuration window ends.

The device will:

* Establish local area network communication with the mobile app via TCP port 6668 * Perform the network configuration process in AP mode via TCP port 6669

AP Hotspot Changes:

The AP hotspot’s SSID and password will be switched to a new setting. Any devices connected to this AP will be forcibly disconnected.

During both BLE and AP configuration, please ensure your network environment is stable, and follow the device instructions to complete the setup. If you encounter any problems, you can press the reset button again to enter a new configuration window.