ECOVACS Winbot W1 Pro Window Cleaning Robot

WINBOT \dot { + } Safety Tether and Carabiner ^ + Safety Battery Power Adapter ECOVACS WINBOT Cleaning Solution Mopping Pad

Instruction Manual Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to change without notice.

Make sure Safety Tether and Carabiner have been connected with WINBOT before using. (Connected by default. Do not disconnect before cleaning.)

Note: Do not use WINBOT on a framed window with a frame narrower than 5 mm (0.2 in).

To enjoy all available features, it is recommended to control your WINBOT via the ECOVACS HOME App.

a. Three Cleaning Mode

Fast Cleaning Mode: Ensure efficient window cleaning

Deep Cleaning Mode: Realize all-round cleaning

Spot Cleaning Mode: Say goodbye to stubborn stains

b. Manual Remote Control, Return to Corner:

Switch between interior and exterior window.

Manual remote control, to clean stubborn stains.

Return to Corner, to let WINBOT return to the specified corner immediately.

c. Auto Water Spray and Manual Water Spray

Auto Water Spray defaulted leaves your windows clean.

WINBOT also supports Manual Water Spray.

d. Smart Reminder of Consumables Replacement

Precise timing reminder, to get a better cleaning experience.

Please ensure the battery is fully charged before using. Charging time will be approx. 2 hours.

*Do not cut the power off when WINBOT is running, otherwise it may lead to the risk of falling.

Connect correctly in the order shown above. Improper connection may cause charging abnormalities or damage to the battery.

It is recommended to use with ECOVACS WINBOT Cleaning Solution. The maximum volume of the Reservoir is about 60 ml, and it can spray for about 60 minutes when the Reservoir is full.

Maximum 60ml

Note: Do not add purified water and filtered water.

Do not add too much cleaning solution to overflow the Reservoir.

Using other cleaners could have an adverse effect on cleaning performance.

If the cleaning solution is used up, you can temporarily use tap water instead. Using the ECOVACS WINBOT Cleaning Solution can have a better cleaning performance.

Before using, wet the Mopping Pad manually.

Twist the Mopping Pad to wring water out. To ensure cleaning performance, wring it out as much as you can.

Stick the Mopping Pad onto the Velcro at the bottom of WINBOT, and press it with your hands to help the Mopping Pad stick firmly.

Properly tie the safety tether to a stable object that cannot be easily moved (e.g. table leg, chair leg, bed leg, sofa leg, curtain rod, stair handrail, etc.), and lock the carabiner as shown below.

Hang the rope and wrap it around the surpport.

Open the carabiner, then attach it to the rope on the other side.

Note: To ensure safety, please make sure to secure the carabiner before use. It is recommended to fasten the Safety Tether with the Carabiner on a firm and safe metal railing.

\textcircled{1} Turn the Power Switch to "I ". \textcircled{2} Attach to the Window.

Method 1: Shortly press \textcircled{1} on WINBOT, then attach it to the glass.

Method 2: Evenly press WINBOT onto the glass for 3 seconds and more to make it firmly attached until you hear a voice prompt.

WINBOT will start cleaning after it has attached to the window successfully.

* Do not stick the WINBOT too close to the edge when cleaning the frameless glass. It is recommended to be more than 10 cm (3.94 in) away from the edge. * WINBOT can only clean flat surfaces. Please make sure that the glass thickness is not less than 3 mm (0.12 in). * Do not put the fan close to hair and other small objects after power on, so as not to block the fan.

For heavily stained glass, please wash or replace the Mopping Pad several times and clean the four Spherical Sensors in time.

During cleaning, press \textcircled{1} on WINBOT or pause it via App.

When cleaning is complete, WINBOT will return to the starting position and beep. Press and hold \textcircled{1} for 5 seconds and more, and remove it after the fan stops working.

Unfasten Safety Tether

Pour out the cleaning solution from the Reservoir.

Remove the dirty Mopping Pad from WINBOT and place a clean new one on it. Then, press the Mopping Pad with your hands to help it stick firmly. Please make sure the Mopping Pad is correctly attached, and do not cover the Spherical Sensors.

* Clean the Velcro at the bottom of WINBOT with a clean brush if it is dirty. Do not wash with water to avoid damage caused by water.

Remove the Mopping Pad. Wash it with tap water, and wring it dry before use.

Washing the Mopping Pad regularly can extend its service life. If the Mopping Pad becomes worn or no longer fits exactly within the fastener area, replace it with a new one to achieve optimal cleaning performance. Explore more accessories at ECOVACS HOME App or at https://www.ecovacs.com/global.

Before maintenance, please make sure that the power switch is set to "I" and the fan stops working.

Fan

Inspect the Driving Treads in ECOVACS HOME App. Stop the Driving Treads if you see dirt on them.

Spherical Sensors

After maintenance, you can install the Mopping Pad to continue cleaning task. Or turn the power switch to " 0 " to end task.

Side Rollers

* After WINBOT reports low battery, please fully charge it before usage and storage to avoid reducing the service life of battery. * If WINBOT will not be used for a long time, please fully charge it and turn it off before storage. Recharge it every six months to prevent the battery from being over-discharged.

Before connection, make sure WINBOT and the mobile phone meet the following requirements:

1. The Bluetooth of the mobile phone is turned on. 2. The WINBOT power switch has been turned on and the indicator light has been lit. 3. Please pair WINBOT in ECOVACS HOME App instead of the phone setting. 4. Co-frequency interference might occur between Bluetooth and Wi-Fi. It is recommended to keep WINBOT close to the mobile phone and distant from the Wi-Fi router during pairing. 5. If the connection failed, please try to disconnect other Bluetooth devices, make sure WINBOT is not connected to other mobile phones, and try again. 6. Bluetooth may be disconnected if WINBOT is too distant from the phone. Try to reconnect at a short distance. 7. For using WINBOT, you need to allow ECOVACS HOME App to obtain access to the location, Bluetooth, and mobile phone storage. If the problems persist after trying the above methods, please contact customer service.

Output power of the wireless module is less than 100 mW.

Note: Technical and design specifications may be changed for continues product improvement.