DREAME L10s Pro Ultra Heat Robot Vacuum and Mop Combo

• Do not place the robot upside down. Do not use the LDS cover, robot cover, or bumper as a handle for the robot.
• Do not use the robot at an ambient temperature above 40°C or below 0°C or on a floor with liquids or sticky substances.
• To prevent damage or harm from dragging, clear any loose objects from the floor, and remove cables or power cords on the cleaning path before operating the appliance.
• Remove fragile or small items from the floor to prevent the robot from bumping into and damaging them.
• Keep hair, fingers, and other body parts away from the suction opening of the robots.
• Keep the cleaning tool out of reach of children.
• Do not operate the appliance in a room where an infant or child is sleeping.
• Do not place children, pets, or any item on top of the robot regardless of whether it is stationary or moving.
• Keep the cleaning solution out of reach of children.
• Use only the officially-approved detergent. Do not add any liquid such as alcohol or disinfectant.
• Do not use the robot to clean any burning objects. Do not use the robot to pick up flammable or combustible liquids, corrosive gases, or undiluted acids or solvents.

• Do not vacuum hard or sharp objects. Do not use the appliance to pick up objects such as stones, large pieces of paper or any item that may clog the appliance.
• Plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
• Do not wipe the robot or the base station with a wet cloth or rinse them with any liquid. After cleaning washable parts, fully dry the parts before reinstalling and using them.
• Please use this product in accordance with the instructions in the User Manual. Users are responsible for any loss or damage that arise from improper use of this product.

• Do not use any third-party battery or base station. The robot can only be used with the model RCLE0301-2 base station.
• Do not attempt to disassemble, repair, or modify the battery or the base station on your own.
• Do not place the base station near a heat source.
• Do not use a wet cloth or wet hands to wipe or clean the base station's charging contacts.
• Do not improperly dispose of old batteries. Unneeded batteries should be discarded at an appropriate recycling facility.
• If the power cord becomes damaged or broken, stop using it immediately and contact after-sales service.

Batteries and Charging

• Make sure the robot is turned off when being transported and kept in its original packaging if possible.
• If the robot will not be used for an extended period of time, fully charge it, then turn it off and store it in a cool, dry place. Recharge the robot at least once every 3 months to avoid over-discharging the battery.

Laser Safety Information

• The laser sensor in this product meets the IEC 60825-1:2014/EN 60825- 1:2014/A11:2021 Standard for Class 1 laser products. Please avoid direct eye contact with it during use.

CLASS 1 LASER PRODUCT CONSUMER LASER PRODUCT EN 50689:2021

Hereby, Dreame Trading(Tianjin)Co., Ltd. declares that the radio equipment type RLL82CE-2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://global.dreametech.com

For detailed e-manual, please go to https://global.dreametech.com/pages/user-manuals-and-faqs

·When operating the robot for the first time, follow it around while cleaning to remove any potential obstacles in time.

·To prevent the robot from not recognizing areas that need to be cleaned, do not stand in front of the robot, threshold, hallway, or narrow places.

·Do not vacuum hard objects like stones, steel balls and toy parts, or sharp objects like construction waste, broken glass and nails, otherwise the ground may be scratched.

Note: Install the side brush until it clicks into place.

Place the base station in a location that is as open as possible with a good Wi-Fi signal. Then insert the power cord into the base station and plug it into the socket.

Place the Base Station and remove any objects that are closer than 1.5 m from the front and 5cm from either side of the base station. Then install the ramp extension plate down to the base station.

Note: To prevent water stains from wetting wood floors or carpets, placing the base station on tile floors or marble floors is recommended.

Press and hold the button on the robot for 3 seconds to turn it on. Place the robot onto the base station with the mop assembly facing toward the washboard. Then you will hear a voice notification when the robot successfully connects to the base station. After the robot is fully charged, the status indicators on the robot and the base station will remain lit for 10 minutes and will then dim.

Note: It is recommended to fully charge the robot before its first use. When the robot cannot be turned on after the battery is depleted, manually connect the robot with the station to charge it.

(1) Remove the dust tank cover and pull out the auto-detergent compartment. (2) Open the upper lid of the compartment and add the cleaning solution. (3) Close the lid of the compartment, put it back it into the base station, and then reinstall the dust tank cover. The cleaning solution will be added into the clean water tank automatically while working.

Note:

·Do not add any liquid other than the officially-approved cleaning solution to help prevent malfunction.

·Install the auto-detergent compartment until it clicks into place.

Take out the clean water tank from the base station and add clean water into the tank. Then install it back into the base station.

Note: Do not add hot water into the water tank, as this may cause the tank to become deformed.

Scan the QR code on the robot, or search "Dreamehome" in the app store to download and install the app.

Open the Dreamehome app, tap " " in the upper right corner, and scan the same QR code on the robot again to add the device. Please follow the prompts to finish the Wi-Fi connection.

·Only 2.4 GHz Wi-Fi is supported.

·Due to upgrades in the app software, the actual operations may differ from the directions in this manual. Please follow the instructions based on the current app version.

Note: If you want to reset Wi-Fi, repeat step 2 and then follow the prompts to finish the Wi-Fi connection.

After configuring the network for the first time, follow the instructions on the app to quickly create a map, and the robot will start mapping without cleaning. The mapping process will be completed when the robot returns to the station, and the map will be saved automatically.

Press and hold the button for 3 seconds to turn on the robot. The power indicator should be illuminated. Place the robot onto the base, the robot should turn on automatically and begin charging. To turn off the robot, move the robot away from the base and press and hold the button for 3 seconds.

When the robot is running, press any button to pause it.

If the robot is paused for more than 10 minutes, it automatically enters sleep mode. The power indicator and charging indicator will turn off. Press any button on the robot, or use the app to wake up the robot.

·The robot will turn off automatically if it is left in the sleep mode for more than 12 hours.

·If the robot is paused and placed onto the base station, the current cleaning process will end.

If the battery is too low, the robot will automatically return to the base station to charge. After charging to the appropriate battery level, it will resume unfinished cleaning tasks.

Note: To use this function, please open it in the app.

When the robot is set to the Do Not Disturb (DND) mode, the robot will be prevented from resuming cleaning and the power indicator goes out. The DND mode is disabled by default at the factory. You can use the app to enable the DND mode or modify the DND period. The DND period is 22:00- 8:00 by default.

·The scheduled cleaning tasks will be performed on time during the DND period. ·The robot will resume cleanup where it left off after the DND period expires.

When the robot is on standby, press briefly the button to enable the spot cleaning mode. In this mode, the robot cleans a square-shaped area of 1.5 × 1.5 meters around it and returns to its starting point once the spot cleaning is completed.

If the robot stops responding or cannot be turned off, press and hold the button \textcircled { 1 } for 10 seconds to forcefully turn it off. Then, press and hold the button for 3 seconds to turn the robot on.

Note: When using the mop assembly for the first time, the robot performs the "Vacuum and Mop" task by default.

Press the button on the robot, or use the app to make the robot start from the base station. Then the robot will plan the optimal cleaning route and perform the cleaning task based on the created map.

·The mop pads will be cleaned before the robot starts mopping, please wait patiently.

·Do not move the base station, the clean water tank, the used water tank, or the washboard during its working.

When cleaning, the robot will automatically return to the base station to wash mop pads based on the mop pad cleaning frequency specified in the app. The base station will automatically refill the robot's water tank and the robot will resume cleanup.

Note: If the robot returns to the base station to wash its mop pads during cleaning, the base station will not automatically empty the dust box.

After the robot finishes a cleaning task and returns to the base station to charge, the base station will automatically start emptying the dust box, and then clean and dry the mop pads.

·If the auto-empty function is turned off in the app, the base station will not automatically empty the dust box.

·The base station will empty the dust box according to the frequency set in the app.

After the robot has completed the task, please clean the used water tank to avoid any odor.

Select "Vacuum then Mop" in the app, and the robot will automatically lift the mop assembly to vacuum the floor. After vacuuming is completed, the robot will return to empty the dust box, and then start mopping after automatically lowering the mop assembly.

Select “Vacuum Only” in the app and the robot will automatically lift the mop assembly and start vacuuming.

Select "Mop Only" in the app, and the robot will check if the mop assembly is installed. If not, manually install the mop assembly, and then the robot will automatically start mopping.

To keep the robot in good condition, it is recommended to refer to the accessory usage in the app or the following table for routine maintenance.

Note: The replacement frequency will depend on your usage of the robot. If an exception occurs due to special circumstances, the parts should be replaced.

1. Select "Base Station Cleaning" in the app, and the robot will exit the base station automatically. Take out the washboard and wait for water to fill the bottom of the base station.

2. Rinse the washboard with clean water, and use the cleaning tool to clean the bottom of the base station.

3. After a moment, the base station will automatically pump out the used water. Then dry it with a soft and dry cloth, and put the washboard back into place.

4. Use the app or briefly press the button on the robot to make it return to the base station.

Note: During cleaning, do not make the robot return to the base station.

1. Discard the dust bag.

Note: Pulling upwards on the handle will seal the bag to prevent the dust and debris from accidentally falling out.

2. Remove the dust and debris from the filter with a dry cloth.

3. Install a new dust bag.

4. Close the cover of the dust tank.

1. Remove the used water tank, open its cover and pour out the used water.

2. Rinse the used water tank with clean water, and use the provided cleaning tool to clean the inner wall of the used water tank.

Note: The float ball in the used water tank is a movable part. Do not apply too much force when cleaning it to avoid damaging it.

1. Press the brush guard clips inwards to remove the brush guard and lift the brush out of the robot.

2. Pull out the brush covers at both ends of the brush as shown in the figure. Use the provided cleaning tool to remove the hair tangled in the brush.

Remove and clean the side brush.

Omnidirectional Wheel

·Use a tool such as a small screwdriver to separate the axle and tire of the omnidirectional wheel. Do not use excessive force.

·Rinse the omnidirectional wheel under the running water and put it back after drying it completely.

1. Open the robot cover and press the dust box clip to remove the dust box. Then remove the filter and tap its basket gently.

Note: Do not attempt to clean the filter with a brush, a finger or sharp objects to prevent damage.

2. Rinse the dust box and filter with water and dry them completely before reinstalling.

·Rinse the dust box and filter with clean water only. Do not use any detergent.

·Use the dust box and filter only when they are completely dry.

Wipe sensors and charging contacts of the robot by using a soft and dry cloth, as shown in the below figure:

Note: A wet cloth can damage sensitive elements within the robot and the base station. Please use a dry cloth for cleaning.

Clean the charging contacts and the signaling area of the base station with a soft and dry cloth.

Clean the auto-empty vents of the robot and the base station with a soft and dry cloth.

Remove the mop pad from the mop pad holder to replace it.

The robot contains a high-performance lithium-ion battery pack. Make sure that the battery remains well-charged for daily use to maintain optimal battery performance.

For more support, contact us via https://global.dreametech.com

Robot

Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

Base Station

Note: Rated Power (during charging and drying) is determined by the power value during full load period.

The built-in lithium-ion battery contains substances that are hazardous to the environment. Before disposing of the battery, make sure the battery is removed by qualified technicians and discarded at an appropriate recycling facility.

– the battery must be removed from the appliance before it is scrapped; – the appliance must be disconnected from the supply mains when removing the battery; – the battery is to be disposed of safely.

Before removing the battery, disconnect the power and run out the battery as much as possible.

Unneeded batteries should be discarded at an appropriate recycling facility.

Do not expose to high temperature environment to avoid risks of explosion.

Under abusive conditions, liquid may be ejected from the battery. If contact occurs, flush with water and seek medical help.

1. Turn over the robot, use a proper tool to remove the screws on the back of the robot, and then remove the cover. 2. Unplug the terminals between the battery and PCB board to remove the battery.

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.