Quick Start
Please review the entire guide before operating the printer.
Safety Notice: Do not connect to power until assembly is complete.
Bambu Studio & Bambu Handy
https://bambulab.com/download
Component Introduction
Screen
Spool Holder
Filament
Spare Hot End
Nozzle Wiping Pad
Power Cord
Unclogging Pin Tool
PTFE Tube
Bambu Scraper
Allen Key H1.5 Allen Key H2
Build Plate（ Pre-installed）
Remove the carboard from the tool head.
Remove the screws as pictured with an Allen Key H2.
Secure the spool holder with two screws from the accessory box.
Remove the three screws with an Allen Key H2 to unlock the hot bed.
into the terminal as pictured.
Attention: Bend the LCD cable towards the opening on the back of the screen as pictured.
Inset the screen back to the slot on the printer, then lock it by pushing it to the left.1. Download the Bambu Handy App. Register and log in to your Bambu Lab account. 2. Connect the printer to power. Follow the instructions on the screen until getting to the page shown on the right side.
3. Use Bambu Handy to scan the QR code on the screen, and bind your printer with your Bambu Lab account.
4. Follow the instructions on the screen to complete the initial calibration. It is normal to have vibration and noise during the calibration process.
DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete.
the filament until it can not move forward.
print.
3
Select " "-" ", and heat the nozzle to the recommended temperature for the filament. Select " "-" "-" " several times until the filament comes out from the nozzle and cannot be pulled out from the PTFE tube anchor manually.
Select "" and select a file to start the first print.
Download Bambu Studio: https://bambulab.com/en/download/studio
Log in to Bambu Studio with your Bambu Lab account, which is the same for the Bambu Online store. Create or open a project.
Slice the model, select your printer and send the model to print.
During printing, you can remotely monitor your print, or pause/stop printing on the
| Item | Specification | |
| Printing Technology | Fused Deposition Modeling | |
| Body | Build Volume(W*D*H) | 256*256*256 mm³ |
| Chassis | Steel | |
| Shell | Plastic & Glass | |
| Toolhead | Hot End | All-Metal |
| Extruder Gears | Steel | |
| Nozzle | Stainless Steel | |
| Max Hot End Temperature | 300°C | |
| Nozzle Diameter (Included) | 0.4 mm | |
| Nozzle Diameter (Optional) | 0.2 mm, 0.6 mm, 0.8 mm | |
| Filament Cutter | Yes | |
| Filament Diameter | 1.75 mm | |
| Heatbed | Compatible Build Plate | Bambu Textured PEI Plate Bambu Cool Plate Bambu Engineering Plate Bambu High Temperature Plate |
| Max Build Plate Temperature | 100°C | |
| Speed | Max Speed of Toolhead | 500 mm/s |
| Max Acceleration of Toolhead | 20 m/s² | |
| Max Hot End Flow | 32 mm³/s @ABS(Model: 150*150mm single wall; Material: Bambu ABS; Temperature: 280°C) | |
| Cooling | Part Cooling Fan | Closed Loop Control |
| Hot End Fan | Closed Loop Control | |
| Control Board Fan | Closed Loop Control | |
| Chamber Temperature Regulator Fan | Closed Loop Control | |
| Auxiliary Part Cooling Fan | Closed Loop Control | |
| Air Filter | Activated Carbon Filter | |
| Supported Filament | PLA, PETG, TPU, ABS, ASA, PVA, PET | Ideal |
| PA, PC | Capable | |
| Carbon/Glass Fiber Reinforced Polymer | Not Recommended | |
| Sensors | Chamber Monitoring Camera | Low Rate Camera 1280 x 720 / 0.5fps, Timelapse Supported |
| Filament Run Out Sensor | Yes | |
| Filament Odometry | Optional with AMS | |
| Power Loss Recover | Yes | |
| Physical Dimensions | Dimensions(W×D×H) | 389*389*458mm³ |
| Net Weight | 12.95kg | |
| Electrical Requirements | Input Voltage | 100-240 VAC, 50/60 Hz |
| Max Power | 1000W@220V, 350W@110V | |
| USB Output Power | 5V/1.5A | |
| Electronics | Display | 2.7-inch 192x64 Screen |
| Connectivity | Wi-Fi, Bluetooth, Bambu-Bus | |
| Storage | Micro SD Card | |
| Control Interface | Button, APP, PC Application | |
| Motion Controller | Dual-Core Cortex M4 | |
| Software | Slicer | Bambu Studio Support third party slicers which export standard G-code such as Superslicer, Prusaslicer and Cura, but certain advanced features may not be supported. |
| Slicer Supported OS | MacOS, Windows | |
| Wifi | Frequency Range | 2412MHz-2472MHz(CE) 2412MHz-2462MHz(FCC) 2400MHz-2483.5MHz(SRRC) |
| Transmitter Power (EIRP) | ≤21.5dBm(FCC) ≤20dBm(CE/SRRC) | |
| Protocol | IEEE802.11 b/g/n | |
| Bluetooth | Frequency Band | 2402MHz-2480MHz(CE/FCC) 2400MHz-2483.5MHz(SRRC) |
| Transmitter Power (EIRP) | ≤20dBm(FCC/SRRC) <10dBm(CE) | |
| Protocol | BLE5.0 | |
Please visit the Bambu Lab Wiki for more setup and maintenance tutorials.
https://wiki.bambulab.com/en/home
Bambulab WikiIf you need support, please try either of the two approaches:
Approach 1:
Approach 2:
Bambu Lab
Enjoy!