Aqara Zigbee Motion Sensor P1

1.Choose an appropriate installation position and make sure the installation surface is clean and flat. 2.Put the sticker on the bottom of the battery cover, determine the detection direction, stick it to the desired installation position, and press hard and evenly for 30 s to make sure it sticks firmly.

1.Choose an appropriate installation position and make sure installation surface is clean and flat. 2.Stick the sensor to the installation pedestal, and press hard and evenly for 30 s to make sure it sticks firmly.

3.Stick holder pedestal in the required area, and press hard and evenly for 30 s to make sure it sticks firmly. In the case of installing on a wall surface, it is recommended that the holder gap faces upward to facilitate adjusting detection direction.

1.Take off the battery cover from its gap with screw driver, and stretch the screw driver into battery compartment lever opening and take off the battery compartment.

2.Install two brand-new CR2450 button batteries into the battery compartment, with one firmly sticking the compartment top on the polar front and the other firmly sticking to the compartment bottom on the polar front.

3.Align to and install the battery compartment based on arrow directions, and then put on the battery cover.

M

B

W

D

O °F )

n

r × 1, Sticker

port

.

Park,

ang

han District,

#

n away from Do NOT use

Beware of moisture, do NOT spill water or other liquids 3. onto the product. Do not place this product near a heat source.4. Do not attempt to repair the product by yourself. All 5. repairs should be performed by authorized personnel. This product is designed only for improving the6. convenience of household life, and for status notifications. If the user violates the product instructions and this warning, the manufacturer is not responsible for an

Unduld be kept n the ante

#

1.Ris correct typ 2.Dis tions. 3.Do 4.Thi If the severe int h.

5.Keep new and used batteries away from children. 6.If the battery compartment does not close securely, stop using the product and keep it away from children. 7.If y or pla e me 8.Dis me can res 9.Lea e sur losion or t 10.A that m mable liq 11.Di m t can re 12.Le re su plosion or 13.A that m mable

liquid or gas.

14.The equipment is only suitable for mounting at heights ≤ 2 m.

#

Hereby, [Lumi United Technology Co., Ltd]

declares that the radio equipment type [Motion Sensor P1,MS-S02] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.aqara.com/DoC/

#

Hereby, [Lumi United Technology Co., Ltd]

declares that the radio equipment type [Motion Sensor P1,MS-S02] is in compliance with Directive 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696).

The full text of the UK declaration of conformity is available at the following internet address: http://www.aqara.com/DoC/.

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your

waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal negative cealth Por more in and c

F pliance st

1. les.

O ons:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

—

— ent and

— rcuit ected.

V technician

posure limits equipment m distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES‐003.

This device complies with RSS‐247 of Industry Canada.

Operation is subject to the condition that this device does not cause harmful interference.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

* Please read this manual carefully and keep it in a safe place. * If necessary, the contents of this manual will be modified or adjusted without special notice.

certified product